Can You Upgrade Old MaxxAir Fan For Remote Capabilities

Question

Question:

I had ordered a fan switch for my MaxxAir vent part # ma00A03550K . I was told this part will not be in until March . It it possible to convert my vent by installing a Circuit board and remove to up date my fan .

asked by: Perry Y

0

Expert Reply:

If your original MaxxAir fan did not come with a remote like # MA00A01150K then you will need to upgrade your old unit with something like the MaxxFan Deluxe Roof Vent w/ 12V Fan, Thermostat, and Remote # MA00-07500K.

The Replacement Handheld Remote for Maxxair Roof Vents # MA00A01150K is only compatible with fans that have an intake and exhaust functions.

This being said, you cannot replace a circuit board/modify a fan that is not compatible with a remote to make it compatible with a remote.

expert reply by: Bryce D

0

Answer 1

The Replacement Operator Mechanism for MaxxAir MaxxFan Plus or MaxxFan Deluxe Roof Vents #MA10-20281K-1AF is the same exact same as the 10a20281k-1af you are looking for.

view full answer...

Answer 2

I've attached an exploded diagram photo of the vent assembly that uses the Replacement Operator Mechanism for MaxxAir MaxxFan Plus or MaxxFan Deluxe Roof Vents #MA10-20281K-1AF for you to check out. You'll need to use it as a guide…

view full answer...

Answer 3

From the numbers you provided it sounds like you have a MaxxFan 4700K model fan. The Replacement Operator Mechanism for MaxxAir MaxxFan Plus or MaxxFan Deluxe Roof Vents #MA10-20281K-1AF is the correct replacement for the MaxxFan 4700K's.

view full answer...

Answer 4

Yes the Replacement Operator Mechanism for MaxxAir MaxxFan Plus or MaxxFan Deluxe Roof Vents #MA10-20281K-1AF that you referenced does fit the MaxxFan vent you have with serial number 2014-02-4751ks-a0157.

view full answer...

Answer 5

It sounds like you need to re-calibrate the zero point on your Lippert Ground Control 3.0 #LC304136 system. Below I've listed out the steps you'll need to follow and will allow you to use the auto leveling again. Zero Point Calibration The…

view full answer...

Answer 6

The noises you described in your question along with the "Out of Stroke" error message you're getting might be indicating some internal damage with the gears on the jack leg(s). The "Out of Stroke" error basically means that…

view full answer...

Answer 7

Is the jack retracting at all? The Lippert Ground Control 3.0 #LC358590 front jacks should be retracting all the way under normal operation so if one of them isn't then you need to try retracting it manually by removing the plug on the motor and…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...