Diameter of 3,500 lb Trailer Axle with Idler Hubs e65GR

Question

Question:

Is this axle 2 and 3/8 inch diameter? To match the U bolts

asked by: Manuel

0

Expert Reply:

Yes, the diameter is indeed 2-3/8 inches for the 3,500 lb axle you asked about, which is the following part number:

- Trailer Axle with Idler Hubs - 5 on 4-1/2 Bolt Pattern - 89" Long - 3,500 lbs # e65GR

So they will work with U-bolts that fit 2-3/8" diameter axles like part # CE15286GA.

expert reply by: Kyle S

0

Answer 1

There are only two real differences between the #e65GR and the Dexter #35545I-EZ-89. One is the compatible wheel size. The etrailer axle works with 13" - 15" wheels while the Dexter axle works with 13" - 17-1/2" wheels. The other…

view full answer...

Answer 2

I'd be more than happy to help you out! If you can measure the hub-face and spring-center measurements of your current axle that will help me know what you're needing. For example, the etrailer Trailer Axle with Idler Hubs #e65GR has a…

view full answer...

Answer 3

If the U-bolts are 9/16 inch diameter, the torque specs should be between 65 to 95 foot lbs. If the U-bolts are 3/8 inch diameter, the torque should be between 30 and 50 foot lbs.

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 6

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 7

The absolute best cushioned equalizer that fits the dimensions you mentioned having would be the MORryde ALLTREK 4000 part #MR89DR as this is only option to provide vertical and horizontal cushioning. This would make a big difference and you'd be…

view full answer...

Answer 8

Since you have a 3,500 lbs axle, I recommend the 4-Leaf Double-Eye Spring for 4,000-lb Trailer Axles item #e22YR. These are for 4,000 lbs axles which will still work great with your Gulf Stream trailer. As far as your 26" measurement goes. If…

view full answer...

Answer 9

Well shackle length is mainly based on the height difference between the front and rear hangers. The rear hanger normally doesn't hang as low as the front so that the shackle can offset the difference and add the ability to move. What is the…

view full answer...

Answer 10

I checked with Lippert and the upper part of the jack should point away from the rear hanger. So if you check out the picture I attached you'll see that the shock "leans" towards the front of the trailer.

view full answer...

Answer 11

The correct orientation of the Lippert Bolt-On Shock Kit w/ Heavy Duty Gas Shocks part #LC281255 is away from the equalizer. Therefore, they will be facing the same direction. I have attached a photo below to better clarify.

view full answer...

Answer 12

The installation process of the Lippert Components Bolt-On Shock Kit part #LC281255 will be the same for a single axle trailer and a tandem/triple axle trailer, just repeated. When installing the shocks, you want to point them away from the shackle…

view full answer...

Diameter of 3,500 lb Trailer Axle with Idler Hubs e65GR

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching