Will Hayes/AL-KO Hydraulic Brake Kit # K23-524-00-2 Work with EOH Actuator

Question

Question:

Will these brakes work with electric actuators

asked by: ROBERT M

0

Expert Reply:

Yes, the Hayes/AL-KO Hydraulic Brake Kit # K23-524-00-2 will work with electric over hydraulic actuators like the HydraStar # HBA-12.

expert reply by: Jameson C

0

Answer 1

Brake actuators designed for drum brakes typically produce around 1,000 psi pressure at most, while disc brake actuators will produce closer to the 1,600-psi pressure that you mentioned in your question. I do not recommend using a disc brake actuator…

view full answer...

Answer 2

The larger Haynes Axles did in fact have a 6 bolt brake mounting flange but the braking assemblies actually only uses five bolts to attach. Therefore, the Hayes/AL-KO Hydraulic Brake Assembly part #K23-524-00 is very what you need. That said, you…

view full answer...

Answer 3

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 4

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 5

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 10

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 11

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 12

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Will Hayes/AL-KO Hydraulic Brake Kit # K23-524-00-2 Work with EOH Actuator

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching