Installing a Box on a 2012 Toyota Sequoia to Support a Roof Top Tent
Question:
can you remove the factory rails and install a box that would take the weight of a roof top tent on a 2012 sequoia?
asked by: Charlie
Expert Reply:
If you are wanting to remove the factory side rails that run front to back on your 2012 Toyota Sequoia, I do not recommend doing so. These rails were meant to be permanently installed on your vehicle and should not be removed. These rails are bolted and sealed to the roof and water could leak into the vehicle if they are removed and other damage could occur such as denting and scratching on the roof.
If you are wanting to remove the crossbars that run from side to side and attach to the side rails, you will not have to remove those crossbars to install an aftermarket roof rack. An aftermarket roof rack like the Thule SquareBar Roof Rack, # TH712400 and # TH710401 will mount to the factory side rails and sit above the factory crossbars so they will not interfere.
If you are wanting to install an aftermarket roof rack to support a roof top tent, it is important that you find the weight capacity of your vehicles roof. An aftermarket roof rack like the Thule Crossroads roof rack has a weight capacity of 165 lbs. This is the highest weight capacity that is offered for an aftermarket roof rack. Even though the weight capacity of the roof rack is 165 lbs, you will still be limited to the roof weight capacity of the Sequoia if it is lower than 165 lbs. You can find the weight capacity of your roof in your owners manual or by contacting a Toyota dealer with your VIN.
Products Referenced in This Question
Thule SquareBar Evo Crossbars - Steel - 53" Long - Qty 2
- Roof Rack
- Crossbars
- Square Bars
- 53 Inch Bar Space
- 2 Bars
- Overhang
- Black
- Thule
more information >
Product Page this Question was Asked From
Evo Raised Rail Feet for Thule Crossbars - Factory Raised Rails - Qty 4
- Roof Rack
- Feet
- 4 Pack
- Thule
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Brake Controller
- Shop: Roof Rack
- Shop: Suspension Enhancement
- Shop: Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Search Results: brake controller wire harness
- Search Results: 3040p
- Shop: K-Source Custom Extendable Towing Mirrors - Electric/Heat w Turn Signal - Textured Black - Pair
- Shop: WeatherTech Side Window Rain Guards with Dark Tinting - Front and Rear - 4 Piece
- Shop: Edge Insight CS2 Comprehensive Gauge Display - 2.4" Color Screen - Toyota
- Shop: Curt Venturer NEXT Trailer Brake Controller - 1-3 Axles - Time Delayed
- Shop: Landing Pad 23 for Yakima SkyLine and Control Towers - Qty 4
- Shop: Firestone Coil-Rite Air Helper Springs - Rear Axle
- Shop: Floor Mats
- Shop: Grille Guard
- Shop: Towing Mirrors
- Shop: Side Window Vents
- Video: Choosing the Right Brake Controller
- Search Results: rv cargo carrier
- Search Results: prodigy 90185
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Search Results: trailer brake controller
- Search Results: brake controller
- Article: Brake Controller Installation: Starting from Scratch
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Video: Redarc Tow-Pro Liberty Brake Controller Review RED24FR
- Article: Rooftop Cargo Carriers
- Video: Tekonsha Prodigy P3 Trailer Brake Controller Review
- Search Results: roof rack
- Video: Choosing the Right Trailer Wiring