Coupler Lock Suggestion For A U-Haul 6x12 Cargo Trailer

Question

Question:

Ill be renting a U-Haul 6x12 enclosed trailer, and wanted to know if this Item # e98894 will fit? Thanks.

asked by: John

0

Expert Reply:

I did some research and it looks like your U-Haul trailer will accept 1 7/8"- 2" ball, so # e98893 will be the correct part, although you should double check yourself. If it turns out yours is larger than that, part # e98894 will work accept a 2" to 2 5/16" ball and would be the correct choice.

expert reply by: Bryce D

0

Answer 1

The etrailer Trailer Coupler Lock - Flat Lip 1-7/8" and 2" Ball Couplers - Aluminum - Yellow #e98897 and the etrailer Trailer Coupler Lock for Flat Lip 1-7/8" and 2" Ball Couplers - Aluminum - Silver #e98893 is the exact same…

view full answer...

Answer 2

I took some measurements off the etrailer Trailer Coupler Lock #e98895 that will help you to determine if this will fit your coupler. The maximum width of the coupler tongue channel is 4-1/2" wide, and 2-3/4" deep. The locking pin is…

view full answer...

Answer 3

Since you are looking to lock your trailer when connected as well as when disconnected, I recommend the Master Lock Trailer Hitch Receiver Lock and Coupler Lock Set - 1-1/4" and 2" Hitches #3794DAT. This kit will give you a hitch pin lock…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 8

We only carry the springs for those heavy duty style ramps. For the springs we have the Ramp Spring - 2K Torque for 1-1/2" Shaft - left hand #RS16933LH and corresponding right hand #RS16933RH. The other parts will need to be either straightened…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 11

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 12

I'm not sure why they include that replacement latch but that is not required for any of the aftermarket hitches or wiring. It is probably something related to the installation of the OEM hitch. The etrailer #e45ZR you referenced is what I would…

view full answer...