Replacement Bearings for a Spindle that Measures 1.055 Inches

Question

Question:

My spindles measure 1.055 on a set of calipers. Are my spindles dead or is there a proper bearing size?

asked by: Steve

0

Expert Reply:

A lot depends on where you are taking that measurement. If you look at the spindle main page I have linked for you, you will see the important spindle measurements I would need to determine what, if any, bearings we carry will fit.

If you have access to the bearings still the best way to determine replacement parts is to get the inner and outer bearing numbers stamped into the metal of the bearings.

If your 1.055 measurement is the C measurement from the spindle main page and the spindle looks like # TRU44FR then the appropriate bearing kit is # BK1-150.

expert reply by: Michael H

0

Answer 1

The Kenda K353 Bias Trailer Tire - 4.80-12 - Load Range B #AM10060 is rated for a max speed of 65 mph. I've attached an article that will assist with other questions you may have as well.

view full answer...

Answer 2

For an RV with a currently installed Dometic Duo-Therm 59516.531 AC unit, I recommend the Advent Air for Dometic Setups, #ACDOM150. This is a 15,000 Btu replacement option that plugs directly into your current Dometic setup and works seamlessly with…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 5

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 6

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 7

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 11

Your math is correct in your trailer weight load example. If a fully-loaded tandem axle trailer weighs 4000-lbs then each of the 4 tires will bear 1/4th of that load, or 1000-lbs. In this case a tire rated for 1300-lbs would provide a good safety…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Replacement Bearings for a Spindle that Measures 1.055 Inches

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching