Recommended Magnetic Brake Lights For A 2016 Ram ProMaster 1500 With Bike Rack Blocking Tail Lights

Question

Question:

I have a 2016 Ram ProMaster high roof. Now that I’m carrying 2 covered e-bikes on a rack in the back my brake lights are obscured. I’d like to add magnetic brake lights just above my existing rear lights. So far all the magnetic brake lights I’ve looked at have magnets at the bottom of the light. I’m looking for lights that would flush Mount to the back of the van. Do you sell anything that would work for me. My hitch has a standard 4 way connector. Thanks!

asked by: Mark T

0

Expert Reply:

I recommend using the Curt Auxiliary LED Indicator Lights # C53201 since we do not have any magnetic lights with the magnetic on the back of the light. These auxiliary lights has a 3M backing to mount to the rear of your 2016 ProMaster 1500 and will plug right in to your 4-pole connector for power. The LEDs in each strip correspond with brake, turn, and running lights.

expert reply by: Kevin C

0

Answer 1

Since magnetic lights won't work with your fiberglass camper shell I recommend the Curt Auxiliary LED Indicator Lights #C53201. These lights simply plug into your 4-way connector and have a 3M adhesive backing so that you can stick them on…

view full answer...

Answer 2

While there is not an option like what you're looking for, I do have another solution. Take a look at the: -Curt Auxiliary LED Indicator Lights #C53201. These lights measure 7" long and will utilize the same 4-pin style like #PE26UR…

view full answer...

Answer 3

First, the trailer should have a sticker or plate on the front of the frame or tongue somewhere that lists its capacity. that is the capacity you will need to go by for the trailer. You are likely correct that it will a capacity over 10,000 pounds…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 9

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 10

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Recommended Magnetic Brake Lights For A 2016 Ram ProMaster 1500 With Bike Rack Blocking Tail Lights

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching