Cost Effective Weight Distribution/Sway Control for 2013 Keystone Summerland 2670BHGS

Question

Question:

Hi, Whats the cheapest weight distribution/sway control hitch that you have that would fit a 2013 Keystone Summerland 2670BGHS?

asked by: Eduardo A

0

Expert Reply:

The most cost effective weight distribution and sway control that is rated properly for your 2013 Keystone Summerland 2670BGHS is the Reese Pro Round Bar part # RE44FR which has a tongue weight range of 600-1,150 lbs.

expert reply by: Jameson C

0

Answer 1

The Reese #RE44FR would indeed offer weight distribution and sway control. The kit includes a 2-5/16 inch trailer ball and the adjustable weight distribution shank. The system is rated for trailers with a 600-1150 lb fully loaded tongue weight. You…

view full answer...

Answer 2

With most weight distribution systems (including this Reese kit part #RE94FR), you can back up with the spring bars connected as long as you are backing up mostly straight, but if you are going to angle the trailer and tow vehicle sharply you need to…

view full answer...

Answer 3

You provided plenty of good info there, and based on that we can get you the right weight distribution system with sway control. What you need with a weight distribution hitch is one in which your loaded tongue weight is in the range of the weight…

view full answer...

Answer 4

If the fully loaded and ready to tow tongue weight of your travel trailer is between 600 and 1150 lbs, the Reese 49913 system which we sell as part #RE44FR would be a good choice. I'll link to an article that explains a few different ways to…

view full answer...

Answer 5

To determine if you need rise, you will measure from the inside top of the receiver on your vehicle and then from the ground to the bottom of the coupler on the trailer. This should be done on as level a surface as possible. The difference will tell…

view full answer...

Answer 6

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...

Answer 7

Long story short, the #RE94FR DOES provide sway control. The Reese 49912 Reese Pro Round Bar Weight Distribution which we offer as part #RE94FR offers effective weight distribution for trailers with tongue weights ranging from 400-800 lbs and offers…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 12

An underslung trailer coupler is one that attaches to the bottom of the trailer frame and an overslung one is one that attaches to the top of the frame. The Replacement Head for Blue Ox SwayPro Weight Distribution Systems part #BXW4011 is for…

view full answer...

Cost Effective Weight Distribution/Sway Control for 2013 Keystone Summerland 2670BHGS

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching