Can Timbren Suspension Kit # TFR1504D Be Added to a 2012 Ford F-150 That Has a Lift Kit

Question

Question:

I have a lift leveling kit 2.5inch in front and 1inch in the rear from rough country. Part of the kit is a 1inch block in addition to the leaf spring. I haul a 700lb motorcycle in the bed and a 5000lb travel trailer with a hitch weight of 500lbs. Will this kit work for me and do I need additional spacers?

asked by: Byron P

0

Expert Reply:

I spoke with with my technical contact at Timbren and he informed me the Timbren Rear Suspension System # TRF1504D that you want to install on your 2012 Ford F-150 will work in conjunction with your current lift leveling kit.

The # TRF1504D comes with spacers which should work in your application, however, he told me that if you still see that you have room in between the bottom of the rubber spring and axle, that you will need an additional spacer such as Timbren 1 inch spacer # A25723-90AH00.

expert reply by: Lori W

0

Answer 1

I recommend the SumoSprings Solo Custom Helper Springs part #SSR-117-47 instead of part #SSR-117-40 for your 2019 Ford F-150. In regards to the SumoSprings, you will always want to have a safety margin and the above will be perfect for your setup.…

view full answer...

Answer 2

The connector for installing a brake controller is located above where the driver's left knee would be, behind the under dash panel located below the steering wheel. If you lower that panel, it'll make finding the connector easier as it's…

view full answer...

Answer 3

In order to add a 7-way trailer connector to a 2022 Nissan Pathfinder you'll need to start with the T-One Vehicle Wiring Harness, part #TK58VR if you don't have the factory tow package or part #TK76VR if you do have the factory tow package.…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 9

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 12

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Can Timbren Suspension Kit # TFR1504D Be Added to a 2012 Ford F-150 That Has a Lift Kit

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching