Are Curt Q20 Legs Compatible with a Curt Q25 5th Wheel Head?

Question

Question:

I have a q20 but would like to switch head to q25 are the legs compatible

asked by: Brandon H

0

Expert Reply:

Yes, the Curt Q20 legs, like item # C16904, do fit with the Replacement Head Unit for Curt Q25 5th Wheel Trailer Hitch item # C16565. The bolt holes line up and the legs are the same height. You will decrease the hitch's capacity to 20,000 pounds though.

expert reply by: Jerred H

0

Answer 1

Congrats on the new truck! Companions don't work with adapters but they have something better if your new 2023 GMC Sierra has the prep package. You can replace your current base with the Replacement Slider Base for B&W Companion…

view full answer...

Answer 2

I think the Yakima ShowDown Kayak Roof Rack and Lift Assist w/ Tie-Downs item #Y04081 would solve your loading problem. Compatibility won't be an issue it fits round, square, aero, and elliptical crossbars. You will need to take a measurement…

view full answer...

Answer 3

I would be happy to! The Thule Force XT Sport Rooftop Cargo Box item #TH6356B would work great with your 2014 Subaru XV Crosstrek. It measures 74-3/4" x 24-3/4" x 16-3/4" and will not mess with your vision. Since your…

view full answer...

Answer 4

To flat tow your 2022 Ram 1500 Rebel with the set up you currently have on your RV you will need the following parts: Base Plate Kit - Blue Ox Direct-Connect Base Plate Kit - Removable Arms item #BLU99FR Supplemental Braking System - Demco SBS…

view full answer...

Answer 5

There's only one set of air bags that is compatible with the B&W Turnover Ball System item #BWGNRK1108 and your 2003 F-350. It is the Air Lift LoadLifter 5000 Ultimate Air Helper Springs with Internal Jounce Bumpers item #AL88390. All…

view full answer...

Answer 6

No, they're about the same. The most difficult part of installing these baseplates is having to remove all of the trim and essentially the entire front end of your Liberty. I have linked both installation instructions below. We've…

view full answer...

Answer 7

It is possible for you to install both the Hopkins Endurance 5th Wheel/Gooseneck 90-Degree Wiring Harness, #HM41158, and the Hopkins Smart Hitch Backup Camera and Hitch Aligner System, #HM50002. The Hopkins Smart Hitch has alternative installation…

view full answer...

Answer 8

With a factory trailer harness all of the wires you are looking for are at the back of that plug. To keep from splicing into the wiring harness there or tying up the plug itself you can use a T-Connector to duplicate the signals. The best way to…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from…

view full answer...

Are Curt Q20 Legs Compatible with a Curt Q25 5th Wheel Head?

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching