Will The Dexter E-Z Flex Suspension Kit Still Fit My Trailer That Has 2-5/8" Shackle Straps?

Question

Question:

My trailer has 2 5/8 shackles on it. Just but the ez flex with heavy duty shackles and wet bolt. Shackles are 2 1/4 will these work

asked by: Thomas C

0

Expert Reply:

You should not have an issue with the shackles straps from the Dexter E-Z Flex Suspension Kit # K71-653-00 being 3/8" shorter than what you currently have on your trailer. This will slightly raise your suspension by around 3/16" if your equalizer is the same height as the Dexter.

I do recommend comparing your current equalizer bolt height with the with the Dexter that is 2-7/8" tall. If your current equalizer is any also shorter this will add to the difference which will slightly raise your suspension. If it is taller it may cause the strap height to level itself out.

expert reply by: Bud M

0

Answer 1

Yes, since your current equalizers have a distance of 7-3/4 inches apart the Dexter Cushioned Equalizers part #K71-653-00 would work great.

view full answer...

Answer 2

Yes, the Road Armor Shock Absorbing Equalizer Kit - Tandem Axle - Qty 2 item #LC696740 will work on axles that are 33" center to center. These equalizers measure 6" from center to center of the two center bolt holes as shown in the included…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Well shackle length is mainly based on the height difference between the front and rear hangers. The rear hanger normally doesn't hang as low as the front so that the shackle can offset the difference and add the ability to move. What is the…

view full answer...

Answer 6

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 10

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 11

I contacted MORryde and this does happen from time to time as the weight of the trailer can spread out the axles due to downward pressure on the springs/suspension. Odds are the 35" wheel base #MR27ZR will be the correct one for you, but they…

view full answer...

Answer 12

The spring hanger placement is going to be determined by your axle spacing. For example, if your axles are spaced 33 inches apart, as shown in the attached diagram, a 7K axle slipper spring, like #e74SR, requires a distance of 28-1/2 inches between…

view full answer...