Largest Size Equal-i-zer Weight Distribution Shank for 2-1/2 inch Hitch Size

Question

Question:

Do they make an 18inch shank in the 2 1/2foot receiver size?

asked by: Rob B

0

Expert Reply:

The Equal-i-zer weight distribution shank we offer with the largest dimensions is the part # EQ94FR which is 12 inches long and is capable of 13 inches of rise and 9 inches of drop.

expert reply by: Jameson C

0

Answer 1

The correct replacement hardware kit for your Fastway e2 4.5k system is the Replacement Hardware Kit for Fastway e2 Weight Distribution Head #FA92-02-9600. The Replacement Bolts for Equal-i-zer Weight Distribution Head #EQ90-02-9400 you asked about…

view full answer...

Answer 2

Rise/Drop shanks like the Equal-i-zer Weight Distribution Shank #EQ94FR are measured from the top of the receiver opening and shank; this shank is 12" and provides a maximum of 13" of rise or 9" of drop when measured from the top of…

view full answer...

Answer 3

In regards to the Equal-i-zer Weight Distribution Shank part #EQ94FR, the distance from the center of the hitch pin hole to the center of the adjustment holes is 8".

view full answer...

Answer 4

You sure can! Weight distribution shanks are not brand specific, you will just need to make sure you use a shank that is the same style as there is two different styles. Based on your picture you will need the #EQ34FR that fits the 2-1/2"…

view full answer...

Answer 5

We do have a replacement regulator for you. The Fairview GR-9950 you have is a 2-stage horizontal propane regulator, and the correct replacement is from JR Products: - Horizontal Low Pressure 2-Stage RV LP Gas Regulator #37207-30385 This will give…

view full answer...

Answer 6

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Largest Size Equal-i-zer Weight Distribution Shank for 2-1/2 inch Hitch Size

Product Page this Question was Asked From

Continue Researching