Compatibility of Kodiak K2R35D With Tie-Down Engineering Hydraulic Disc Brake Actuating Coupler

Question

Question:

I purchased a Kodiak Disc brake kit model # K2R35D. My trailer currently has a TDE model #LP7000 CLASS IV actuator. I am assuming the actuator will work given I previously had disc brakes. Is this correct?

asked by: Joe

0

Expert Reply:

You're absolutely correct! As long as your existing hydraulic coupler is for disc brakes, it'll work just fine with the Kodiak # K2R35D Disc Brake Kit you've purchased. If you click the provided link, you can see a video of the disc brake kit being installed.

expert reply by: Mike L

0

Answer 1

I attached a picture that has all of the mounting hole dimensions of the Kodiak Disc Brake Bracket #KCMB10RD.

view full answer...

Answer 2

The diameter of the center hole on the rotor included with the #K2R35D is exactly 3" and fits a 5 on 4-1/2 bolt pattern. This is designed to fit over standard idler hubs on a 3,500 lb axle.

view full answer...

Answer 3

The mounting flange bolt pattern for the Dexter Electric Brake Kit for 4 Bolt or 5 Bolt Flange #23-105-106-09 measures 3-1/8" between the top two holes, 2-1/2" between the lower two holes, and 3-3/8" between the top and bottom holes.…

view full answer...

Answer 4

The brake mounting flange on the Dexter Trailer Axle Beam with 4" Drop E-Z Lube Spindles #7685269 has mounting holes that are 2-7/8" apart on center (see attached).

view full answer...

Answer 5

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 6

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 7

The AL-KO trailer hub part number 8700 that you have is a 3,500 lb trailer hub/drum with a 5 on 4-1/2 inch bolt pattern. Based on that the #AKHD-545-35-EZ-K is the correct fit and would work great.

view full answer...

Answer 8

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 11

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 12

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Compatibility of Kodiak K2R35D With Tie-Down Engineering Hydraulic Disc Brake Actuating Coupler

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching