Brake Mounting Flange Bolt Pattern for 3.5K 95" Long Dexter Trailer Axle

Question

Question:

What is the brake backing plate 4 bolt pattern measurements? Thanks

asked by: Mark R

0

Expert Reply:

The brake mounting flange on the Dexter Trailer Axle Beam with 4" Drop E-Z Lube Spindles # 7685269 has mounting holes that are 2-7/8" apart on center (see attached).

expert reply by: Jon G

0

Brake Mounting Flange Bolt Pattern
(click to enlarge)

Answer 1

I attached a picture that has all of the mounting hole dimensions of the Kodiak Disc Brake Bracket #KCMB10RD.

view full answer...

Answer 2

The mounting flange bolt pattern for the Dexter Electric Brake Kit for 4 Bolt or 5 Bolt Flange #23-105-106-09 measures 3-1/8" between the top two holes, 2-1/2" between the lower two holes, and 3-3/8" between the top and bottom holes.…

view full answer...

Answer 3

You're absolutely correct! As long as your existing hydraulic coupler is for disc brakes, it'll work just fine with the Kodiak #K2R35D Disc Brake Kit you've purchased. If you click the provided link, you can see a video of the disc brake…

view full answer...

Answer 4

The diameter of the center hole on the rotor included with the #K2R35D is exactly 3" and fits a 5 on 4-1/2 bolt pattern. This is designed to fit over standard idler hubs on a 3,500 lb axle.

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 7

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

There really isn't a particular maximum trailer weight that is used to determine when brakes need to be added to both axles of a tandem axle setup. While I do still recommend checking your local laws, I am also not aware of any general laws that…

view full answer...

Answer 10

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 11

Depending on how the trailer was made, there will be a few spots you can check to identify the axle. First, if the trailer was pre-made by a specific company, you may be able to find this information in either the paperwork or on a placard somewhere…

view full answer...

Answer 12

If your trailer has 7 wires running all the way back to the brakes, then yes, you can tap into the existing wiring. Each of your new brakes will have two wires for the brake magnet. One wire is for 12 volt power to the brake magnets and the other…

view full answer...

Brake Mounting Flange Bolt Pattern for 3.5K 95" Long Dexter Trailer Axle

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching