What Reflector Ring Fits the LED Trailer Tail Light # STL73RB?

Question

Question:

Which is the reflector ring for the STL73RB ?

asked by: Joe L

0

Expert Reply:

I confirmed with my contact at Optronics that the reflector ring that you need for the LED Trailer Tail Light w/ Flange - Stop, Turn, Tail - Submersible # STL73RB is the Snap-on Reflector Ring for STL78RB Series LED Lights # A78RXB.

expert reply by: Bob C

0

Answer 1

We do offer many high-efficiency LED-type trailer stop/turn/tail lights in the 6-1/2 x 2-1/4-inch size of the Optronics #ST70RBTK that you referenced. All can be seen on the linked page. All lights shown are submersible. You can choose from either…

view full answer...

Answer 2

Our installer here will spray the light with some lubricant around where the light meets the grommet and then will use a screwdriver to pry the light out first, and then the grommet. If you check out the install video I attached you will see this…

view full answer...

Answer 3

I went out in to our warehouse and pulled a Optronics Trailer Light #STL78RB and a Snap-on Reflector Ring for STL78RB Series LED Lights #A78RXB to show you what they look like together. I attached a picture and a video I shot also.

view full answer...

Answer 4

Since there is no type of cross reference available for taillights on RVs like your 2019 Forest River Grey Wolf 27DBH, in order to figure out how the correct replacement taillight, you will simply need to measure your taillight, which will determine…

view full answer...

Answer 5

The lens will typically have a DOT number, but not a model number. A replacement lens is usually determined by the model number of the light itself. There should be a model number printed on the back of the light. If you have a square incandescent…

view full answer...

Answer 6

The Lippert 2420801 hub is an 8k hub with an 8 lug bolt pattern so for a replacement you'd just need the part #8-285-10UC3-A.

view full answer...

Answer 7

Did you pull any fuses or disconnect the battery before installing the Replacement Hydraulic Pump for Lippert Level Up Leveling Systems #LC58TF Vic? Have you tried unplugging and replugging the connector back in to see if a pin needed to be reseated?…

view full answer...

Answer 8

Hey Tim, thanks for reaching out! The Stromberg Carlson Base Pad Extreme for RVs and Trailers #SC33VR have a 6,000 lb rating for each Base Pad Extreme so you're looking at a total of 36,000 lbs for this kit of 6. Ideally your jacks will have the…

view full answer...

Answer 9

Hi Michael, While we don't have any way of knowing what winch stand goes on any specific trailer, it is possible we have an option for a winch stand for your Karavan trailer. The only option we have for a stand is the CE Smith Winch Stand…

view full answer...

Answer 10

We can get you a good replacement, though there is actually no longer a TDE brand. But that actuator is simply a bolt-on, 7,500 lb actuator that couples to a 2" hitch ball, and per the owner's manual does not have a lockout (so it is for…

view full answer...

Answer 11

The best way to identify the seal needed, is to get the number that is stamped or imprinted on the seal. You may have to remove the seal in order to see the numbers. If you cannot find the number on the seal, if you can find the numbers on the inner…

view full answer...

Answer 12

The best option we can offer you is the Trailer Idler Hub Assembly part #AKIHUB-545-2-EZ-2K which will be a direct replacement for the Dico Trailer Hub Assembly part 45263 so long as you the Double Lip Grease Seals part #RG06-010. The Trailer Idler…

view full answer...