Does Weld-On Pipe Mount Come With Trailer Valet JXS Trailer Jack TV34FR

Question

Question:

I need to weld mount this jack. Is there a separate drilled weld on pipe mount included with the bolt on stuff?

asked by: James H

0

Expert Reply:

A weld-on pipe mount is not included or available for the Trailer Valet JXS Trailer Jack w/ Footplate and Drill Powered Option - Side Mount - Sidewind - 2K # TV34FR.

There isn't an option to weld on the Trailer Valet jacks, and the only pipe-mounted option for a Trailer Valet is also a bolt-on jack, the 5k Trailer Valet JXS Trailer Jack # TV64FR.

expert reply by: Kyle S

0

Answer 1

The best solution for raising the trailer tongue would be a base pad/jack stand like the #SC86MR. Raising the ground up with something like this is typically better than trying to extend the jack. Two of these stacked together would give you an…

view full answer...

Answer 2

I spoke to Dutton-Lainson about the Drop Leg Trailer Jack with Footplate - 2,000 lbs part #DL97MR and they informed me that it will take 8 cranks of the handle to raise or lower the jack 1".

view full answer...

Answer 3

You can use the Trailer Valet JXS part #TV64FR on an I-beam trailer frame but it would need to fit around the I-beam instead of fitting into it.

view full answer...

Answer 4

The Trailer Valet #TV64FR JXS 5K trailer jack is a pipe mount swivel jack that can be removed from the trailer by pulling the pin shown in the provided photo. If you click the provided link, you can see a video showing a typical installation.

view full answer...

Answer 5

Probably our best option would be the trailer fender part #HP66VR which is 13 inches wide and 36 inches long. This would easily accommodate a tire that is 31 inches in diameter and 10.5 inches wide.

view full answer...

Answer 6

We have a few wide trailer fender options that would work well. The widest being the part #HP66VR which is 13 inches wide and metal. This would probably be your best option. The part #CE19504-2 is 11 inches wide and is black plastic. The part #HP29VR…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Does Weld-On Pipe Mount Come With Trailer Valet JXS Trailer Jack TV34FR

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching