How Many Turns Does it Take to Raise Dutton-Lainson Drop Leg Jack- 2,000 lbs 1 Inch

Question

Question:

How many crank-revolutions per inch to raise or lower? Thanks in advance.

asked by: JR

0

Expert Reply:

I spoke to Dutton-Lainson about the Drop Leg Trailer Jack with Footplate - 2,000 lbs part # DL97MR and they informed me that it will take 8 cranks of the handle to raise or lower the jack 1".

expert reply by: Conner L

0

Answer 1

The best solution for raising the trailer tongue would be a base pad/jack stand like the #SC86MR. Raising the ground up with something like this is typically better than trying to extend the jack. Two of these stacked together would give you an…

view full answer...

Answer 2

A weld-on pipe mount is not included or available for the Trailer Valet JXS Trailer Jack w/ Footplate and Drill Powered Option - Side Mount - Sidewind - 2K #TV34FR. There isn't an option to weld on the Trailer Valet jacks, and the only…

view full answer...

Answer 3

You can use the Trailer Valet JXS part #TV64FR on an I-beam trailer frame but it would need to fit around the I-beam instead of fitting into it.

view full answer...

Answer 4

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 5

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 6

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 9

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 10

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 11

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 12

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

How Many Turns Does it Take to Raise Dutton-Lainson Drop Leg Jack- 2,000 lbs 1 Inch

Product Page this Question was Asked From

Continue Researching