How To Install Load Resistor Kit For LED Turn Signals That Flash Quickly
Question:
My tail light has a brake light and license plate light built in should I wire the load resistor across the brake light lead and ground or the running/license plate lead and ground.
asked by: Mike H
Expert Reply:
You will want to wire in a load resistor to any LED bulb that flashes quickly. Basically, the vehicle thinks a bulb is burnt out so you need to add a small load (resistor) to allow the bulb to stop flashing. The resistor gets wired into the bulb's positve and negative wires or leads. For this, I recommend using Load Resistor Kit for LED Turn Signals - 50 Watts - 6 Ohm - Qty 2 # DI34ZR which comes with 2 resistors. So if you have 4 bulbs flashing, you will need 2 of these kits for a total of 4 resistors.
In other words, if your brake light and the running/license plate light are both flashing, you will need to install a resistor into each circuit/bulb.
Product Page this Question was Asked From
Load Resistor Kit for LED Turn Signals - 50 Watts - 6 Ohm - Qty 2
- Accessories and Parts
- Trailer Lights
- Load-Resistor Kit
- Diamond
more information >
Continue Researching
- Shop: Load Resistor Kit for LED Turn Signals - 50 Watts - 6 Ohm - Qty 2
- Q&A: When Switching to LEDs if I put in a LED Flasher do I Need Resistors
- Video: Review of Diamond Lights - Load Resistors - DI34ZR
- Search Results: di34zr
- Q&A: Solution for Rapid Signal Flashing on Utility Bed with LED Lights
- Shop: Putco LED Light Bulb Load-Resistor Kit - Aluminum
- Shop: Optronics Load Resistor for LED Lights - Male PL-3 Plug and Female PL-3 Plug - Qty 1
- Shop: Peterson Load Resistor Harness for LED Turn Signals - Male and Female PL-3 Plug - 50 Watt - 10 Ohm
- Q&A: Troubleshooting LED Lightbar Flicker Installed on 2020 Chevy Silverado 2500
- Shop: Trailer Wiring
- Q&A: Troubleshooting LED Tail Light Bulbs Flickering when Vehicle Lights are Turned Off
- Q&A: After Installing Load Resistors Brake Lights Come On and Turn Signals Hyperflash with Headlights On
- Q&A: Trailer Lights Blinking Really Fast When Connected to 7-Way on 1997 GMC Yukon
- Q&A: Troubleshooting Right Turn Signal Not Working on Trailer Taillights
- Video: Review of MORryde RV Cargo Slides - Sliding Generator Tray - MR89RR
- Video: MORryde RV Generator Slide Out Tray Review
- Shop: MORryde RV Generator Slide Out Tray - 19-1/4" x 23" - 100 Percent Extension - 250 lbs
- Video: Putco LED Light Bulb Load-Resistor Kit Installation - 1995 Chevrolet CK Series Pickup
- Shop: 7- and 4-Pole Trailer Connector Socket w/ Mounting Bracket - Vehicle End
- Shop: Optronics Load Resistor for LED Lights - Male PL-3 Plug and Pigtail - Qty 1
- Article: Trailer Wiring Diagrams
- Video: Review of Command Electronics Trailer Lights - Triple LED Stop Turn Tail Reverse - CE44VR
- Video: Choosing the Right Trailer Wiring
- Shop: Trailer Hitch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: 25580
- Shop: Fifth Wheel Hitch
- Search Results: 44649
- Article: How to Choose the Right Trailer Hitch Class
- Search Results: 68149