Availability of Leaf Spring Hanger/Equalizer Kit for Springs that are 2 inches Wide

Question

Question:

I have some 7000lb axles tandem they are 2inch wide do you have any kits for 2inch leaf springs ? I can send more information if you do but most places do not.

asked by: Phillip R

0

Expert Reply:

We have tandem axle slipper spring hanger/equalizer kits like with the part # APT6SE but if the leaf springs are double eye springs we don't have anything based on your width.

expert reply by: Jameson C

0

Answer 1

I went ahead and attached a diagram that shows the spacing of the hangers on the 6-Leaf Slipper Spring w/ Hook End for 8,000-lb Trailer Axles - 29-1/2" Long #e46SR. This is the spacing you will use with the Tandem-Axle Trailer Hanger Kit…

view full answer...

Answer 2

The slipper spring should sit on the hanger bolt somewhere in the center of the flat part so that it allows a bit of movement as the suspension articulates. The curved ends will generally going to keep the spring from moving too far if the…

view full answer...

Answer 3

You will actually just need kit #APT6SE-36 which is the same thing only the equalizers in it are 13-1/8 inches long. The hardware with each is specific to the kits so some of the other parts are different but for 2 inch slipper springs and 13-1/8…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

Answer 6

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 7

Well shackle length is mainly based on the height difference between the front and rear hangers. The rear hanger normally doesn't hang as low as the front so that the shackle can offset the difference and add the ability to move. What is the…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 11

I contacted MORryde and this does happen from time to time as the weight of the trailer can spread out the axles due to downward pressure on the springs/suspension. Odds are the 35" wheel base #MR27ZR will be the correct one for you, but they…

view full answer...

Answer 12

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Availability of Leaf Spring Hanger/Equalizer Kit for Springs that are 2 inches Wide

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching