Dexter 7 x 1 3/4 Hydraulic Brake Assembly Kit

Question

Question:

Does this come with the retention spring parts two pins, four spring washers and two springs or just the two shoes?

asked by: Sandor

0

Expert Reply:

The 7" x 1-3/4" Hydraulic Brake Shoe/Lining # bp04-050 is just the shoes for one wheel, however we do offer Dexter Hydraulic Trailer Brake Kit - Uni-Servo - 7" - Left and Right Hand Assemblies # 23-398-399 which is a complete left and right side kit that includes brake assembly, mounting bolts, and nuts.

Unfortunately, we do not offer the hardware separately.

expert reply by: Bryce D

0

Answer 1

It appears your 2003 Jayco Qwest uses an A-frame tongue which would require a Demco Hydraulic Brake Actuator #DM8609502 to be welded on in place of your Atwood 85736 master cylinder. We do have the Demco Hydraulic Brake Actuator #DM72VR which bolts…

view full answer...

Answer 2

An E3 error code on the Fogatti RV Tankless Water Heater #LSB64FR would indicate that the unit is going into overheat protection mode. Fogatti recommends cutting the power to reset the unit 1-2 times to solve the issue. If the issue isn't…

view full answer...

Answer 3

Brakes like the Dexter #23-398-399 that are rated for 2,500 lbs have the capacity to work with 1,800 lb axles, but to get the right brakes you'll need to know your brake's mounting flange bolt pattern as well as your drum diameter. The…

view full answer...

Answer 4

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey David, from previous customers of ours who have the same 2020 Keystone Raptor 424 we have determined that your pin box style is the Lippert 1621 which means for a Gen-Y gooseneck adapter you'd want the #GY58GR that you referenced.

view full answer...

Answer 7

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 8

Your surge coupler will have either a sticker or an engraving on it, typically near where the coupler is located. If you can get me that information and what you're needing to replace on it I'd be more than happy to help you find what…

view full answer...

Answer 9

Are you basically asking how much length would this coupler add to the tongue of your trailer?

view full answer...

Answer 10

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 11

Hey Al, this is a great question but since you have free-backing plates now you would never need to mess with the manual lock out of your Atwood coupler.

view full answer...

Answer 12

The Replacement Shock Absorber Spring Kit #TK71-758-00 is the correct shock for your UFP Surge Brake Actuator. The picture you included does not specify if it is for a disc or drum brake set, so I have found both for you to choose from. Disc Brake…

view full answer...