Would Trailer Hitch for 2001 Mazda B3000 Truck Also Fit 1996 Model

Question

Question:

Would a 2001 mazada tow hitch assemply fit my mazda 1996 B3000

asked by: Ray

0

Expert Reply:

The hitches we carry for the 1996 Mazda B3000 like the Curt # 13138 fit models from 1994 to 2010 so yes a hitch from a 2001 would also fit a 1996 model.

expert reply by: Jameson C

0

Answer 1

From what I could find it appears that models that do have the ground effects will have a trim piece at the bottom of the rear bumper that also wraps around to the sides of the vehicle. I included a picture with an arrow pointing to the area in…

view full answer...

Answer 2

We can help you find a suitable hitch for your 2001 Mazda MPV. For your 2001 Mazda MPV we do offer two sizes and classes of trailer hitch receiver, both a 1-1/4-inch Class II type and a higher-capacity 2-inch Class III. Correct fits for these will…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

It is a bit confusing since there isn't any detailed info from Curt that explains it, but I can help you out. Ground effects for your 2003 Mazda MPV van are an additional trim package, and if you take a look at the accompanying photo, you can see…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 7

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 8

To me it makes the most sense to put a Bike Rack #HLY64FR on the flat towed vehicle rather than above the tow bars. Especially on heavy e-bikes as they are difficult to lift that high onto the rack, but also as it only makes sense to have the rack on…

view full answer...

Answer 9

You are on the right track. The only way we have that will allow you to use the Thule T2 Pro Xtr Bike Platform Rack part #TH69TX with the 2.5" receiver tube opening on your truck would be with adapter. For this, I recommend the Brophy Hitch…

view full answer...

Answer 10

To keep your back end from squatting, I recommend the Coil SumoSprings Custom Helper Springs for Coil Spring Suspension item #CSS-1094R. These insert into your rear springs and keep your suspension from being pushed down by the weight of your…

view full answer...

Answer 11

I recommend the Roadmaster Dual Hitch Receiver Adapter, 10" Drop/Rise item #RM-077-10. This adapter was designed for this type of set up. Your Jeep Rubicon and Swagman E bike rack weigh well below the 10,000 lbs maximum capacity of this hitch. I…

view full answer...

Answer 12

Hey John, Hellwig is a bit new to our selection so I haven't gotten to get my hands on as many of their products as compared to Roadmaster. The experience I've had so far has been somewhat disappointing in terms of overall quality…

view full answer...

Would Trailer Hitch for 2001 Mazda B3000 Truck Also Fit 1996 Model

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching