Troubleshooting Powered A-Frame Jack that Won't Raise or Lower Manually or Electrically

Question

Question:

the jack will not extend either powered of manually.

asked by: Ron C

0

Expert Reply:

Sounds like the inner screw of the Bulldog Powered Trailer Jack part # BD500200 that you have is damaged which would require the jack to be replaced. If it's less than 5 years you might be able to get it warrantied but otherwise you'd need to get a new jack.

expert reply by: Jameson C

0

Answer 1

I do have a solution for you, however the replacement lower assembly for the Husky 4,500 pound trailer jacks is no longer available from the manufacturer, nor is the Husky Brute. I recommend simply replacing the trailer jack with a new unit like the…

view full answer...

Answer 2

That is a custom trailer build I believe. I asked another Expert here and neither of us have seen anything like it. Since you are adding a plate to the top and bottom of your tongue, the Bulldog Jack Support Plate - A-Frame - 2.3" Square Hole…

view full answer...

Answer 3

The Trailer Valet JXS Trailer Jack #TV64FR is the closest we have to the Round, Pipe Mount Swivel Jack #TJP-7001S-B with a power drill attachment. This jack is only rated for up to 5,000lbs versus 7,000lbs like the jack you found. It also has a bolt…

view full answer...

Answer 4

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 5

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 6

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 7

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 10

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 11

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 12

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Troubleshooting Powered A-Frame Jack that Won't Raise or Lower Manually or Electrically

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching