Which Replacement Mounts Do I Need for My Thule T2 Pro?

Question

Question:

Hi, for this part, I am having a hard time finding the right one. I think we have a Thule T2 Pro XTR 9034. It seems like we have a less common earlier model where the mounting bolts are closer together. Can you get me the measurement of the mounting plate? Its the section in the attached photo. Thank you

asked by: RJ B

0

Expert Reply:

I went ahead and called my contact at Thule and he confirmed that as long as you have the older Thule T2 Pro XT or the newer Thule T2 Pro XTR, the part number you need for the replacement mounts is either # 7524703001 (for the tray nearest to the vehicle) or # 7524703002 (the tray furthest from the vehicle).

expert reply by: Bob C

0

Answer 1

There is a replacement shank/stinger for the Thule T2 XTR with the part #TH37MY but the one for the Classic would not work on the XTR.

view full answer...

Answer 2

I spoke with Swagman and they let me know that the Replacement Shank for Swagman XTC4 4-Bike Rack #SP329 measures 14" overall and is made from 1/4" steel. Since you're looking for a bit longer receiver bar, I recommend going with the…

view full answer...

Answer 3

The tube you need for your Thule T2 Classic Bike Platform Rack is part of the backbone. You will have to purchase the entire backbone assembly in order to get the tube you need. The part you need is the Replacement 2" Hitch and Backbone Assembly…

view full answer...

Answer 4

We do have the replacement spar assembly for your Thule T2 Classic bike rack, though it is a different part than what you mentioned, as that is a part for the T2 Pro XT. Instead, the correct spar for the T2 Classic is the following: - Replacement…

view full answer...

Answer 5

To remove the Thule One-Key Lock Core from your old Spar Tube and install it in your Replacement Spar Tube #7524703002 you will just need the Universal Change Key #853-1251. With the lock core unlocked you will just insert the change key and remove…

view full answer...

Answer 6

We still have parts for the Thule Roadway #TH912XTR. To secure your bike rack in your receiver, you will want the Thule Snug Tite Hitch Lock and Anti-Rattle Device #THSTL2 for a locking option or just the replacement pin #853-5917. For your cradles,…

view full answer...

Answer 7

It sounds like the core is not responding to the key. I recommend using some penetrating oil on the inside of the lock core and then driving around for a little bit to let the vibration allow the oil to get into all the small areas. If it is just a…

view full answer...

Answer 8

I have attached the complete instructions manual for the Thule T2 Pro XTR 2 Bike Platform Rack #TH83JV below which details both the assembly instructions and the correct bike loading process. Most of the rack comes pre-assembled and it's really…

view full answer...

Answer 9

The upright arm on the Thule T2 Pro XTR Bike Rack for 2 Bikes part #TH83JV can be replaced yes, that said you must buy this as an assembly with the tray. The Replacement Spar Tube Assembly for Thule T2 Pro XT part #7524703001 for the one closest to…

view full answer...

Answer 10

I have a solution for you. Here at etrailer, we highly discourage using a wheel-mount bike rack like the Thule T2 Pro XTR Bike Rack for 2 Bikes - 2" Hitches - Wheel Mount #TH83JV when using bikes with fenders. The wheel mounts increase the…

view full answer...

Answer 11

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 12

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...