Is the # SR25879 Pin 5/8"?

Question

Question:

Is the # SR25879 pin 5/8inch or 1/2?

asked by: Jake O

0

Expert Reply:

The diameter of the Replacement Hitch Bolt with Lock Washer for QuietRide Stainless Steel Ball Mounts # SR25879 is 5/8".

expert reply by: Bob C

0

Answer 1

There is a solution for you, but the HitchMate Threaded Lock #HE6001 will not work with your Kuat Transfer 2. You'd want the Cable Locks and Hitch Lock for Kuat Transfer 2 Bike Rack #PTSCLK12, which includes a hitch lock that attaches to your…

view full answer...

Answer 2

I compared the dimensions of the pin you provided, and we don't sell a lock housing individually that would work with it. Your best bet would be to buy a locking pin/lock housing combo like #HE6001. I've provided a diagram of the pin…

view full answer...

Answer 3

Although it mounts to the sides of the front frame members instead of the tow hooks, the EcoHitch #EH59FR front mounted receiver would install so that the receiver tube sits behind the license plate holder. The Curt #C31018 and Draw-Tite #65049 would…

view full answer...

Answer 4

When installed, the EcoHitch #EH59FR front receiver will sit in the middle of the front bumper, between the tow hooks as shown in the photo I've provided for you. With the receiver sitting in the middle of the bumper, you won't need to worry…

view full answer...

Answer 5

Thanks for the picture! I have a solution for you but it does look like your dual steering stabilizer bars will be in the way for you to mount the Draw-Tite Front Hitch item #65049. Instead you will want to use the EcoHitch Hidden Front Mount Trailer…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

For a roof rack to be compatible on your 2020 Jeep Wrangler with Sky One-Touch Power Top, it can't be mounted on the top of the roof and it needs to be high enough for the folding roof to clear. What you need are tall gutter-mounted roof racks.…

view full answer...

Answer 11

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 12

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Is the # SR25879 Pin 5/8"?

Product Page this Question was Asked From

Continue Researching