Replacing Dexter Torsion Axles On Trailer

Question

Question:

I need a trailer axle but in not sure which one the old one says dexter 69-46ep

asked by: Albert R

0

Expert Reply:

It looks like you have 3,500lb Dexter axles; while we do not have torsion axles exactly like that, we have another option that may work for you. If you don't need any lift or drop, which it looks like you don't, then I would look into the Timbren Axle-Less Trailer Suspension System 3,500 lbs # ASR3500S05 which is a straight spindle setup. You can simply weld-in or bolt-in the new assembly and then run 2" tubing through both assemblies for reinforcement as seen in the attached demonstration video. One thing to note is that if you have a tandem trailer then you will need to swap out both axles for this setup, not just one; you cannot have two different styles of suspension on a trailer.

You can then re-build your hub assemblies. You can use Easy Grease Trailer Idler Hub Assembly for 3.5K Axles - 5 on 4-1/2 - Pre-Greased # AKIHUB-545-35-EZ-K and Trailer Hub and Drum Assembly - 3.5K E-Z Lube Axles - 10" Diameter - 5 on 4-1/2 - Pre-Greased # AKHD-545-35-EZ-K. I attached several demonstration videos for you to check out.

expert reply by: Andrew N

0

Replacing Dexter Axles On Trailer
(click to enlarge)

Answer 1

The best replacement brake kit assembly that you're looking for is one that we have branded under the etrailer name: - Hydraulic Brake Kit - Uni-Servo - Free Backing - Dacromet - 10" - Left/Right Hand - 3,500 lbs #AKFBBRK-35-D This has the…

view full answer...

Answer 2

In regards to wheel size compatibility, this comes from the hub as the surface area on said hub is what dictates the wheel size. Therefore, if you're already using 13" wheels with your existing hubs then there won't be any issues with…

view full answer...

Answer 3

To determine which hydraulic drum brake assemblies will fit on your 2,500 pound axles you'll need to measure the dimensions of your drums. For example, if your drums are 10 by 2-1/4 inches you can use #AKFBBRK-35-D. Since you have a boat trailer…

view full answer...

Answer 4

To get the best braking power for your boat trailer you would want to have disc brakes on both axles. If you happen to be limited to one axle then you would want the rear outfitted. With a 5,000lb boat you likely have two 3,500lb torsion axles. The…

view full answer...

Answer 5

I recommend the Hydraulic Brake Kit #AKFBBRK-35-D for upgrading your original backing plates. This assembly has dacromet coating on the backing plates, stainless steel springs and an aluminum hydraulic cylinder to resist rust and corrosion. And they…

view full answer...

Answer 6

Yes, the Demco #40716-15 Hydraulic Brake Kit will fit your needs for a 10" X 2.5" assembly. When measuring the drum use inside measuerments as shown in the attached photo. You will just want to confirm your flange bolt pattern is 4 on…

view full answer...

Answer 7

Your trailer must have free backing brakes if you have never used the surge brake actuating coupler reverse lockout. If you did not have free backing brakes, your brakes would most likely brake even if they didn't lock up when you back up because…

view full answer...

Answer 8

We have everything you will need to add surge brakes to your Aspen Camper. I have attached a link that will take you to our available selection of brake assemblies. You can filter through the different assemblies based on your camper's axle…

view full answer...

Answer 9

The biggest difference between the servo styles that you'll notice is between free backing plates and the others. The free-backing plates will allow your trailer to back up without having the brakes lock up. With surge brakes typically when you…

view full answer...

Answer 10

It is certainly possible for any axle to wear out enough over time to need replacing. Since the suspension is built into a torsion axle if the suspension part was to wear out pretty much the only solution would be to replace the axle. If the…

view full answer...

Answer 11

Yes, your best and most cost effective option for increasing the braking on your trailer would simply be to add brakes to the other axle. You really can't go with a larger size without replacing the axle and switching to disc won't increase…

view full answer...

Answer 12

The #20TA-BLKIT brake line kit you referenced is indeed compatible with the #AKUBRK-35-D Hydraulic Brake assemblies you'd looked at, the line kit is compatible with bolt disc and drum brake systems. The brake assemblies will be compatible with…

view full answer...

Replacing Dexter Torsion Axles On Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching