Complete Hydraulic Brake Assy. for 2006 EZ Loader Trailer with Oil Bath Hubs

Question

Question:

2006 easy loader trailer #3200 oil bath hubs. Looking at # 40716-15, pulled drum its 10-inch x ? possible 2.5inch or 2.25inch depends how i hold the tape. the brake pad is 2.25 inch for sure. will these fit, will 2.25 work in a 2.5inch hub?

asked by: Rob M

0

Expert Reply:

Yes, the Demco # 40716-15 Hydraulic Brake Kit will fit your needs for a 10" X 2.5" assembly. When measuring the drum use inside measuerments as shown in the attached photo.

You will just want to confirm your flange bolt pattern is 4 on 4". Measurement between center of one mounting hole to center of the next mounting hole. I have attached another photo depicting this.

expert reply by: Les D

0

click to enlarge

Answer 1

To determine which hydraulic drum brake assemblies will fit on your 2,500 pound axles you'll need to measure the dimensions of your drums. For example, if your drums are 10 by 2-1/4 inches you can use #AKFBBRK-35-D. Since you have a boat…

view full answer...

Answer 2

The best replacement brake kit assembly that you're looking for is one that we have branded under the etrailer name: - Hydraulic Brake Kit - Uni-Servo - Free Backing - Dacromet - 10" - Left/Right Hand - 3,500 lbs #AKFBBRK-35-D This…

view full answer...

Answer 3

In regards to wheel size compatibility, this comes from the hub as the surface area on said hub is what dictates the wheel size. Therefore, if you're already using 13" wheels with your existing hubs then there won't be any issues with…

view full answer...

Answer 4

Your trailer must have free backing brakes if you have never used the surge brake actuating coupler reverse lockout. If you did not have free backing brakes, your brakes would most likely brake even if they didn't lock up when you back up because…

view full answer...

Answer 5

The Hydraulic Brake Kit part #AKFBBRK-35-D are just what you need to replace the hydraulic free-backing braking assemblies on your trailer. The hydraulic 10" braking assemblies are all going to have the same 2-1/4" depth which is measured…

view full answer...

Answer 6

We have everything you will need to add surge brakes to your Aspen Camper. I have attached a link that will take you to our available selection of brake assemblies. You can filter through the different assemblies based on your camper's axle…

view full answer...

Answer 7

I recommend the Hydraulic Brake Kit #AKFBBRK-35-D for upgrading your original backing plates. This assembly has dacromet coating on the backing plates, stainless steel springs and an aluminum hydraulic cylinder to resist rust and corrosion. And they…

view full answer...

Answer 8

The biggest difference between the servo styles that you'll notice is between free backing plates and the others. The free-backing plates will allow your trailer to back up without having the brakes lock up. With surge brakes typically when you…

view full answer...

Answer 9

The thread size that the brake line fittings of the Hydraulic Brake Kit #AKFBBRK-35-D that you referenced is 3/8"-24. This is the standard size that brake lines and fittings are made for.

view full answer...

Answer 10

The #20TA-BLKIT brake line kit you referenced is indeed compatible with the #AKUBRK-35-D Hydraulic Brake assemblies you'd looked at, the line kit is compatible with bolt disc and drum brake systems. The brake assemblies will be compatible with…

view full answer...

Answer 11

Yes, your best and most cost effective option for increasing the braking on your trailer would simply be to add brakes to the other axle. You really can't go with a larger size without replacing the axle and switching to disc won't increase…

view full answer...