Compatible Entry Door Locking Latch For A 2005 Jayco Jay Series 1600 Pop Up Camper

Question

Question:

Would this item fit a 2005 jayco jay serie 1600 pop camper. Existing lock is broke and unable to lock door Thanks

asked by: Eric

0

Expert Reply:

The Global Link RV Entry Door Locking Latch Kit # 295-000019 will fit your door if the cutout hole is 2-1/2" wide x 3-1/2" tall to 3" wide x 4" tall. Manufacturers do not list the door handles they use so the only way to replace them is to have the brand and serial number of the door handle to look up the exact size or just take it off and measuring the cutout hole to find a compatible fit.

expert reply by: Kevin C

0

Answer 1

Depending on the window style and size. I would suggest either the Rubber Window Edge Weather Strip for RVs - Press In - 20' Long x 1/2" Tall #SR43FR or the Rubber Window Edge Weather Strip for RVs - Press In - 20' Long x…

view full answer...

Answer 2

I have another option for you, but the Camco RV Vinyl Trim Insert #CAM25202 is not for windows, entry doors, compartment doors, or vents. We have a few window weather strips available which I have listed below so you can see what size works for…

view full answer...

Answer 3

For your 2002 Jayco Heritage Pop-Up camping trailer, I recommend the Global Link RV Entry Door Locking Latch Kit with Keyed Alike Option - Black #295-000019. This latch fits doors that are 1-1/4 inches to 1-1/2 inches thick and installs into latch…

view full answer...

Answer 4

There is not a cross reference for campers that allows me to look up what latch set is installed on your pop-up camper. However, you can view the linked video below that shows how to remove/replace a door latch. It is actually very simple and only…

view full answer...

Answer 5

For a replacement entry door latch we have the Global LInk RV Entry Door Latch #295-000019 which is a universal design for RVs like what you have. We do not have replacement springs though for what you have.

view full answer...

Answer 6

The Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector #C55316 is what you need if there is a factory connection near the rear bumper like pictured on the driver's side. If it is there, then you will use the Universal…

view full answer...

Answer 7

As long as the controller is installed parallel to the direction of travel, and is level on a side-to-side plane, you can certainly mount the Tekonsha Prodigy P3 #90195 at a 45 degree angle to match the slope of your vehicle's dashboard. If you…

view full answer...

Answer 8

I am including a link to a FAQ page on trailer wiring. It will show the 7-Way trailer connector functions and the 7-Way vehicle connector functions. At the bottom of the page is a chart that will list the wire colors by vehicle manufacturer. This…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...