Roadmaster Falcon 2 Tow Bar Repair Kit

Question

Question:

I have a Roadmaster Falcon 2 tow bar model 252321-10 serial # 044471. What is the correct rebuild kit part number?

asked by: Chris W

0

Expert Reply:

The correct rebuilt kit for your Roadmaster Falcon 2 tow bar # RM-520 with serial number 044471 is the part # RM-910003-60 that you referenced.

expert reply by: Jameson C

0

Answer 1

Since everything on your Roadmaster Falcon 2 tow bar still functions, it sounds like you just need the Complete Repair Kit for Roadmaster Falcon 2 and BlackHawk Tow Bars #RM-910003-60 to replace the bushings and springs. This will help you get things…

view full answer...

Answer 2

Over time, dirt and debris can build up on the retracting portion of the tow bar arms. When the arms retract, this dirt is carried into the interior of the tow bar, and can foul out the locking mechanism on one or both of the tow bar arms. This is…

view full answer...

Answer 3

The repair kit that you will need for your Falcon 2 Tow Bar, #RM-520, is the Locking Pin Repair Kit, #RM-910003-80. The Autowlok feature on your tow bar is not engaging, so this repair kit will replace the inner locking mechanism which includes the…

view full answer...

Answer 4

Do you have the RM-525 or the RM-520? Is it a tow bar designed for a Blue Ox or Roadmaster base plate? And which specific bolt is it?

view full answer...

Answer 5

Your memory does serve you right and both arms on your Roadmaster Falcon 2 #RM-520 are designed to "lock up" as this is not a non-binding tow bar; whether or not they've been able to get the arms to lock without performing the two sharp…

view full answer...

Answer 6

I'm assuming you're speaking of the 3/4 inch bolt and nut that joins the yoke to the stinger assembly, which are items #14 and #15 as shown in the provided diagram. If that's what you're speaking of, then yes we do offer that nut and…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 12

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Roadmaster Falcon 2 Tow Bar Repair Kit

Product Page this Question was Asked From

Continue Researching