Solution for Fulton F2 Trailer with Bad Gear Box Housing

Question

Question:

HI, looking for the gearbox housing for the fulton f2 jack?

asked by: Brady

0

Expert Reply:

That's not a part we can get as Fulton does not offer it as a replacement part. Only solution we have would be a new jack like the F2 part # F1413140334.

expert reply by: Jameson C

0

Answer 1

If you are speaking of the gearbox cover or cap on the top of the jack that is secured by four screws, the replacement is part #F500135. If you are speaking of the black plastic piece below that cover that wraps around the jack with the hole for the…

view full answer...

Answer 2

Since the Vault Hybrid Lubrication System uses a specific hybrid oil which you did not use when re-greasing your bearings, you will not want to reuse the Vault bearing protectors. Instead I recommend going with the Bearing Buddy bearing protectors,…

view full answer...

Answer 3

From what I was able to determine, your CR 21352 grease seal is a Chicago Rawhide 21352 and should be a double lipped seal with a 2.125" ID and 3.376" OD. To replace a seal of that size you'll want to use the #GS-2125DL, which has the…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 6

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 7

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 8

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 9

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 12

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Solution for Fulton F2 Trailer with Bad Gear Box Housing

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching