Can Thule Hullavator Assisted Kayak Carrier Lock to Roof Rack

Question

Question:

I have Yakima towers and older Yakima round bars with their own tower locks already, so the racks cannot be stolen. I just ordered the Thule Hullavator Pro lift assist cradles, now can these hullavator cradles also have their own locks? Otherwise, I feel if I just install the Hullavator, it’s an expensive item, and at risk of theft. Thanks.

asked by: Thomas L

1

Helpful Expert Reply:

To lock the Thule Hullavator part # TH898 all you need is a set of two lock cylinders from Thule with part number # TH450200 and you'd be set. This will prevent the expensive rack from being stolen from your roof rack!

expert reply by: Jameson C

1

Answer 1

Yes, with the Thule Hullavator #TH898, you will need Thule One-Key System Lock Cylinders - Qty 2 #TH450200.

view full answer...

Answer 2

There is not a general restriction from Thule that says two Hullavator Kayak Carriers #TH898 can't be used on a Thule roof rack. As long as the crossbars on your Ford Escape have the required length for two sets and a sufficient weight…

view full answer...

Answer 3

Only the latest version of the Thule Hullavator part #TH898 is compatible with aero shaped crossbars. So your options at this point would be the new Hullavators and an aero shaped roof rack like you want (expensive I know...), or a square bar roof…

view full answer...

Answer 4

Each Hullavator #TH898 will take up 28-1/2" of bar space. So you would need to have at least 57 inch bars. So you need to find a bar that will give you at least 57 inches but also have 4-8 inches beyond the feet. Best bet is to get the longest…

view full answer...

Answer 5

Thank you so much for purchasing your 2 Thule Hullavators #TH898 with us here at etrailer. If you are looking to put same-key lock cores in your carriers, you need the Thule One-Key System Lock Cylinders - Qty 4 #TH450400. This kit comes with 4 lock…

view full answer...

Answer 6

For your 2018 Honda HR-V to be compatible with the Thule Hullavator Pro Kayak Carrier and Lift Assist with Tie-Downs #TH898, you have to use slightly longer crossbars. The Hullavator requires 4-8 inches overhang to give clearance. In order to give…

view full answer...

Answer 7

Yes, the Thule Hullavator Pro Kayak Carrier part #TH898 will work with the Thule WingBar Evo Crossbars. These are just an updated version of the Thule AeroBlade Crossbars. The Hullavator can be attached to the WingBar in one of two ways, with…

view full answer...

Answer 8

The Thule WingBar Evo crossbars do not require you to cut the rubber inside the channel at all; the rubber simply separates when you push into the channel so you don't have to worry about that. You can install the Thule Hullavator #TH898 by using…

view full answer...

Answer 9

The minimum cross bar spread to install the Thule Hullavator Pro Kayak Carrier and Lift Assist with Tie-Downs part #TH898 is 24" apart. So the bars must be at least 24" apart for safe use. The maximum cross bar spread is 36" so it only…

view full answer...

Answer 10

The Thule Hullavator part #TH898 that you referenced requires a set of crossbars that run from left to right on the roof of the vehicle to install. It does not come with them but if you can let me know what year Nissan Rogue you have I can help you…

view full answer...

Answer 11

If you are contemplating whether to transport 2 50-pound fishing kayaks on your 2009 Honda CR-V or your 2007 Honda Pilot, there are crossbar systems that are compatible with both vehicles. For your 2009 Honda CR-V with flush rails, I recommend the…

view full answer...

Answer 12

To find out if the Rhino-Rack T-Load Hitch Mounted Load Assist and Support Bar RTL002 will fit beyond the spare tire on your 2010 Toyota FJ Cruiser, there is a simple measurement you can take. Holding a straight edge (like a yardstick) against the…

view full answer...