Would Curt PowerRide Fifth Wheel Hitch Fit in Same Rails as Curt Q24 Hitch

Question

Question:

I currently have a Curt 24, will the 30 fit into the existing rails?

asked by: Paul

0

Expert Reply:

Yes the Curt PowerRide fifth wheel hitch part # C22ER would fit the same rails you have now for your Curt Q24 hitch.

expert reply by: Jameson C

0

Answer 1

I may have a solution for you, but it looks like you've got the a Curt Q20 sliding hitch and #C16022 adapter for your Ram OEM pucks, which won't be compatible with a Curt PowerRide 5th Wheel Trailer Hitch - Dual Jaw - 30,000 lbs #C22ER. The…

view full answer...

Answer 2

According to the manufacturer, the Curt PowerRide 5th Wheel Trailer Hitch #C22ER weighs 152 lbs.

view full answer...

Answer 3

Manufacturers have found that the pivoting can lead to issues with certain pin boxes (Rota-Flex) and can actually cause an opposite effect hurting your ride quality. The Curt PowerRide #C48BR has a bit of give to it to help with coupling and ride…

view full answer...

Answer 4

The #C16022 does add a few inches to the height of a fifth wheel hitch. Typically you can raise the pin box of the trailer higher up into the trailer frame which will allow a taller fifth wheel hitch to fit. You do want to be sure you have at least 6…

view full answer...

Answer 5

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 10

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 11

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 12

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Would Curt PowerRide Fifth Wheel Hitch Fit in Same Rails as Curt Q24 Hitch

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching