Can Two Of The Curt 2-Wire to 3-Wire Converter C56196 Be Used To Convert RV To 3-Wire System
Question:
I want to convert a 2 wire taillight on a RV to a 3 wire taillight. Can I buy 2 of the 56196 controllers and use them separate instead of running and fishing all the wires through the body of the RV. All the wires for the individual lights are in a hole behind each tail lights. Would I need a resistor for the blinker and will the unit sense signals correctly using it only on one side? Thanks,
asked by: John T
Expert Reply:
Yes you can use two of the Curt 2 to 3 Wire Tail Light Converter # C56196, one on each side of your RV to convert its 2-wire system to work with 3-wire lights. Doing it this way will prevent you from having to run the wiring from one side to the other on your RV.
You will not need to use any resistors, and the turn signals will work just fine.
I included a video of the # C56196 for you to take a look at.
Product Page this Question was Asked From
Curt 2 to 3 Wire Tail Light Converter
- Tow Bar Wiring
- Splices into Vehicle Wiring
- Tail Light Converter
- Universal
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Vehicle Tow Bar Wiring
- Shop: Timbren Axle-Less Trailer Suspension - Heavy Duty - Long Spindle w/ 2" Lift - 5 Bolt - 3.5K
- Shop: Curt 2 to 3 Wire Tail Light Converter
- Shop: Timbren Axle-Less Trailer Suspension w Idler Hubs - Standard Duty - No Drop - 5 on 4-1/2 - 3,500 lbs
- Video: Curt Tow Bar Wiring C56196 Review
- Video: Review of a Trailer Suspension Enhancement System - TASR35HDS07
- Shop: Hopkins Tail Light Converter - LED Compatible
- Shop: Cotter Pin - 1/8" Thick x 1-3/4" Long
- Shop: Westlake ST225/75R15 Radial Tire w/ 15" Liger Aluminum Wheel - 6 on 5-1/2 - LR E - Gray
- Shop: Replacement Center Cap for 15" or 16" Aluminum Viking Series Wheels - Chrome
- Search Results: rims
- Search Results: grease
- Q&A: Which Hubs Fit the Timbren Heavy-Duty Axle-Less Trailer Suspension # TASR35HDS06 with 2" Lift
- Q&A: Recommended Timbren Axle Less System and Hub with 5 on 5-1/2 Bolt Pattern
- Q&A: Recommended Idler Hubs for Timbren Heavy-Duty Axle-Less Trailer Suspension 3,500 lbs
- Video: Dexter E-Z Lube Axles Trailer Idler Hub Assembly Review and Installation
- Video: Timbren Axle-Less Trailer Suspension System Installation
- Q&A: Curt 2 To 3 Wire Tail Light Converter Install
- Q&A: Add Separate Trailer Turn Signal Lights
- Q&A: Could Curt Taillight Converter Box C59196 be Used to Convert Combined Taillight Circuits to Separate
- Q&A: Troubleshooting Taillight Feedback When Using 2 to 3 Taillight Convertor
- Shop: Trailer Hitch
- Search Results: timbren
- Article: Trailer Wiring Diagrams
- Search Results: bearing buddy
- Article: How to Choose the Right Trailer Hitch Class
- Shop: Trailer Wiring
- Search Results: trailer jack
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Base Plate for Tow Bar
on Tow Bar Wiring
