Picking Out Replacement Brake Assemblies for 2004 Keystone Laredo

Question

Question:

What brakes would I need for my 2004 Keystone Laredo fifth wheel trailer? I think its 28ft.

asked by: Tony

0

Expert Reply:

There are a few 2004 Keystone Laredo models available but I am pretty confident that yours has 3,500 lb axles which would mean that for the left hand side you'd want the part # AKEBRK-35L-SA and then for the right hand side part # AKEBRK-35R-SA which are self-adjusting.

If you have something different though let me know and I'll see if we can help.

expert reply by: Jameson C

0

Answer 1

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 2

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 3

I'd be happy to help you out, John! To replace the brakes on your 5th wheel trailer you need the etrailer Electric Trailer Brakes #AKEBRK-7-SA which come with a self-adjusting feature so once you initially set them up you won't have to adjust…

view full answer...

Answer 4

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 7

I currently have three diffrent self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes which are attached for you below. eTrailer Electric Trailer Brake Kit part #AKEBRK-35-SA (3,500 Axles) Dexter…

view full answer...

Answer 8

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 11

The recommended lug nut torque for your 7,000lb axle depends on a few factors like wheel size, stud size etc. Check out the attached photo which shows the torque specs for a variety of applications. I see you were looking at the Dexter Nev-R-Adjust…

view full answer...

Answer 12

Based on the GVWR of your 2019 Jayco North Point 315RLTS it does seem like you have 7k axles. I recommend verifying this information to be sure. These axles typically use the #14125A outer and #25580 inner bearing found in the Timken #TMK92VR.…

view full answer...

Picking Out Replacement Brake Assemblies for 2004 Keystone Laredo

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching