What Gauge Wire Was Bulldog Winch Shut Off Switch # BDW20248 Designed For

Question

Question:

What size gauge wiring can I use with this cut off switch? Would 2gauge fit?

asked by: Adil R

0

Expert Reply:

Due to how the Bulldog Winch 500 Amp Shut-Off Switch # BDW20248 attaches to the wiring using studs that you could use basically any ring terminal. This is rated for 500 amps though so a very heavy gauge wire was intended to be used so I'd assume a zero gauge and close to that would be no issue at all.

expert reply by: Jameson C

0

Answer 1

The Bulldog Winch 500 Amp Shut-Off Switch - Metal Housing #BDW20248 will operate up to and at 500 amps whether it is intermittent use or continuous. The 500 Amp battery disconnect switch should only be used for powering on and off the main power…

view full answer...

Answer 2

A diode like the part #RM-690 is a great idea but the only issue is that is has a max load of 85 amps. A standard 5,000 lb winch, like the ComeUp DV-5000si #CU645010, will greatly exceed the 85 amp rating of the diode so it would be useless. What…

view full answer...

Answer 3

The studs of the Bulldog Winch Shut Off Switch part #BDW20248 are 5/16 inch in diameter.

view full answer...

Answer 4

For a roof rack to be compatible on your 2020 Jeep Wrangler with Sky One-Touch Power Top, it can't be mounted on the top of the roof and it needs to be high enough for the folding roof to clear. What you need are tall gutter-mounted roof…

view full answer...

Answer 5

We do offer tow bar setups that can attach to the D-rings on the Warn Elite Bumper. Your will need to use a D-ring adapter to connect the tow bar. For the adapter you have the following options: 1" Thick D-Rings #RM-035-1 3/4" Thick…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

I have a solution for you, however, I would not recommend mounting a tow bar directly to a bumper on a Jeep, whether it is OEM or an aftermarket bumper. Jeep does not recommend towing the Wrangler with the OEM bumper because it was not designed to…

view full answer...

Answer 8

The stoplight switch #RM-751490 and the monitor light that's included in the Demco SBS Stay-IN-Play DUO Supplemental Braking System #SM99251 do the same job, so you wouldn't need it if you decided to go with the Stay-IN-Play DUO. The…

view full answer...

Answer 9

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 10

There have not been any major changes to the Stay-In-Play system since 2016, so I believe it certainly would be worthwhile (and a $$$ saver) to remove the major parts from the now-wrecked car. Provided you can get that done for a reasonable cost.…

view full answer...

Answer 11

Correct, you do need a working battery for activation and continual operation of the Demco SBS Stay-IN-Play DUO Supplemental Braking System #SM99251 and Demco Stay-IN-Play DUO Supplemental Braking System w/ Wireless Coachlink Monitor #DM86VR. If you…

view full answer...

Answer 12

You will first want to check the fuses on your tow vehicle. Some vehicles could have fuses for operating the turn signals and brake lights of a towing package. You will want to check if they are installed and working properly. The next thing is to…

view full answer...

What Gauge Wire Was Bulldog Winch Shut Off Switch # BDW20248 Designed For

Product Page this Question was Asked From

Continue Researching