Distance From Mounting Holes To Bottom Fender Lip On Tandem Axle Teardrop Trailer Fenders

Question

Question:

how far up from the bottom fender lip is the center measurement for the mounting holes.. thank you

asked by: Mike L

1

Helpful Expert Reply:

In regards to the Tandem Axle Teardrop Trailer Fenders for Boat Trailers part # HP34VR, the distance from the center of the mounting holes to the bottom of the fender lip is 4" which you can see in the attached photo.

expert reply by: Conner L

1

etrailer Fender Mounting Hole Dimensions
(click to enlarge)

Answer 1

Since you said your tires were rubbing I would go with a hanger setup that is a little taller like the part #AP233-H248 which has 3-1/4 inch front/rear hangers and 3-5/8 inch center. Also, while the 60/40 rule for axle placement is a great starting…

view full answer...

Answer 2

To add a second axle to your trailer, apart from the axle you'll need another set of hangers that need to be welded on, another leaf spring,four more U-bolts, an equalizer, four more shackle straps, and eight more shackle bolts. You'll have…

view full answer...

Answer 3

The first and easiest thing you should check is that the trailer is being towed level. If the trailer is nose high or low that can cause the equalizers to not sit level. You will need to select the correct rise/drop ball mount so that the trailer…

view full answer...

Answer 4

For the Tandem Axle Teardrop Trailer Fenders for Boat Trailers - Steel - 14" Wheels #HP54VR, it really depends on how you install the fenders. If you bolt the fenders onto your boat trailer, they will definitely not be able to accommodate 300…

view full answer...

Answer 5

You could use a taller equalizer but you would also need to use taller front and rear hangers as well. Everything will have to be raised equally so if you go up 2 inches in one spot you have to go up 2 inches in all spots. If you do not raise it at…

view full answer...

Answer 6

You can convert a single axle trailer to a tandem axle but it's more extensive than just putting the extra axle on there. The current axle does need to be repositioned for proper tongue weight. You will also need to cut off the current hangers…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 11

Assuming your tires are in good shape without any bulges the easiest way to determine if you have a bent spindle is to take a straight edge that is longer than the tire and lay it across the tire parallel with your trailer frame and then measure the…

view full answer...

Answer 12

As long as the weight capacity is inline with your trailer/axle rating and the measurements match your current springs, the number of leaves in a spring pack does not matter. The difference between a 3 and 4 leaf spring pack within the same weight…

view full answer...

Distance From Mounting Holes To Bottom Fender Lip On Tandem Axle Teardrop Trailer Fenders

Product Page this Question was Asked From

Continue Researching