How To Wire the Dual-Face LED Trailer Light

Question

Question:

It would be nice to have a wiring diagram for the light to know which wire controls what.

asked by: Glen P

1

Helpful Expert Reply:

In regards to the Dual-Face LED Trailer Light part # STL52ARB; the black wire goes to the running light circuit which is usually a brown wire on the trailer, the red wire goes to the stop/turn circuit which is usually a green/yellow wire on the trailer, and the white wire is for the ground circuit.

expert reply by: Conner L

1

Answer 1

The Dual-Face LED Stop/Turn/Tail and Parking Light - 42 Diode - Post Mount - 4" Round - Red/Amber #STL52ARB can be installed vertically or horizontally. The red side faces the rear of the vehicle or trailer and the orange faces the front. This…

view full answer...

Answer 2

Most likely the original lights you are replacing used the mounting hardware/stud to make the ground connection to the trailer frame. This is not unusual. A light such as #ST52AA uses the mounting stud to establish ground while the similar light…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 5

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 6

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 10

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

Your math is correct in your trailer weight load example. If a fully-loaded tandem axle trailer weighs 4000-lbs then each of the 4 tires will bear 1/4th of that load, or 1000-lbs. In this case a tire rated for 1300-lbs would provide a good safety…

view full answer...

How To Wire the Dual-Face LED Trailer Light

Product Page this Question was Asked From

Continue Researching