Which Bearing Kit Fits a Dexter 5100lb Axle?

Question

Question:

Would you please direct me to the correct bearing kit for my 5100 LBS dexter axles... Axle # 7608228 Pics attached. Thank you!

asked by: Clark L

0

Expert Reply:

Thanks for the pictures of the axle information!

Based on the information you provided your axle uses the following components:

Inner bearing # 25580
Inner race # 25520
Outer bearing # LM67048
Outer race # LM67010
Grease Seal # GS-2250DL

All of these components are included in the Bearing Kit # BK3-300 you were looking at.

I included a video of the # BK3-300 for you to take a look at.

expert reply by: Samuel C

0

Customer Picture
(click to enlarge)

Answer 1

I reached out to my contact at Dexter and with the serial number you provided they were able to track down the correct replacement bearings for the spindles on your axles. For the inner bearing you will use part #25580 for the bearing itself and…

view full answer...

Answer 2

I was unable to find any information with the numbers on your axle, unfortunately. However, you can contact the manufacturer of the trailer and they should be able to tell you exactly which inner and outer bearings you have. If for some reason they…

view full answer...

Answer 3

The bearings your Lippert 5,200 lb axle has are part #LM67048 and #25580 and the grease seal is #RG06-070. For a cotter pin you'd need just the #165649.

view full answer...

Answer 4

Pulling the wheels and hubs off of your 5th wheel trailer is the best option when trying to identify what wheel bearings and seals are installed. On the back of the wheel bearings there usually is printed a part number like #L44643. With these…

view full answer...

Answer 5

You can verify that the 10-19 grease seal included in Bearing Kit #BK2-100 is the correct one for your spindles by taking two measurements. First you want to measure the rear hub bore where the seal is inserted. The seal's outer diameter needs to…

view full answer...

Answer 6

The Progressive Dynamics Inteli-Power RV Converter and Battery Charger #PD9160ALV will work great to charge your 80 amp hour Lithium battery with your Honda 2000 generator. Going with a higher rated charger would be a bit overkill for your battery…

view full answer...

Answer 7

For a similar 60 amp converter that can charge a lithium battery you'd want the part #PD9160ALV but the part #PD9260C can only charge lead acid batteries.

view full answer...

Answer 8

Yes, axle spread and wheel base by definition are the same measurements. You will measure from the center of one axle to the center of the 2nd axle to determine what you axle spread is. This may be difficult as some wheels and covers will make this…

view full answer...

Answer 9

The Camco Automatic Changeover 2-Stage Propane Regulator for Dual Propane Tanks #CAM59005 is able to be utilized as manual changeover if you simply keep one tank turned off at the cylinder valve. There is not a specific manual changeover regulator we…

view full answer...

Answer 10

It really comes down to knowing what Equaflex you have now or the dimensions of them and then picking out the matching MORryde kit. The part #MR87ZR is made to fit the most common dimensions as it is for 33 inch wheelbases and has 6-1/2 inches…

view full answer...

Answer 11

You can check the condition of your hub's races by carefully removing all bearing grease with a rag to expose the actual surface of the races. When they are completely free of grease, etc., inspect them for any signs of scoring (very slight…

view full answer...

Answer 12

Thanks for providing a photograph of your trailer axle sticker. I was able to speak with my contact at Dexter Axle and find out the bearing sizes. You need the etrailer #BK3-300 Bearing Kit. This will get you bearings, seals, and races. At this very…

view full answer...

Which Bearing Kit Fits a Dexter 5100lb Axle?

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching