Replacement Landing Gear Legs for RV that are 29-1/2 inch Measured Outer Tubes

Question

Question:

I measure 29 and 1/2 on the existing black part on the 2004 Sprinter 5th wheel I have -

asked by: Mary R

0

Expert Reply:

We do have the correct 29-1/2 inch replacement legs for Venture landing gear that is measured on the outer tube like you mentioned, which is the following:

- Replacement Lead Jack with Drop Leg # LG-179013

- Replacement Follow Jack with Drop Leg # LG-179014

expert reply by: Jameson C

0

Answer 1

Yes, the Replacement Motor for Stromberg Carlson Electric Landing Gear #LG-142178 has been confirmed to replace the ADTH 1RV-200 landing gear motor you currently have so it would work for you.

view full answer...

Answer 2

The gearbox #RVLG-RDBOX for the Landing Gear Set w/ Handle #RVLG-8HDL can be mounted in the horizontal or vertical position. I went out to the warehouse and tested both the gearbox and lead leg together and the pins that hold the gearbox in place…

view full answer...

Answer 3

When adjusting the height of a pin box such as #LC1191191 it is important to support the pin box when removing the bolts. I recommend 2 or 3 buddies to give you a hand and make sure no one is beneath the pin box while raising or lowering it. With the…

view full answer...

Answer 4

You have a few choices for replacement landing gear with legs that measure 29-1/2 inches, depending on what weight capacity you need and if you want manual or electric landing gear. - Stromberg Carlson #LG-1: Electric Landing Gear with 5,500 lb…

view full answer...

Answer 5

I went out to our warehouse to take a look at the Replacement Follow Jack w/ Drop Leg #LG-179014 that you mentioned. The leg itself does indeed have a length of exactly 29-1/2 inches. The distance between the welded tabs, inside to inside, is right…

view full answer...

Answer 6

Good news! I was able to go out to the warehouse and measure the etrailer landing gear #RVLG-8HDL for you. I found that the distance between the weld stops from the outside to outside is 17-1/2 inches and from the inside to the inside of the weld…

view full answer...

Answer 7

It sounds like the new higher-capacity Stromberg Carlson motor #LG-196308 you're using is drawing more power than your old motor did. It is likely that your wire gauge and/or fuse value are inadequate for the extra current drawn by the…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

To determine the best landing gear option for your 1997 Forest River Sierra you'll need to measure the where your weld-stops sit to see if there is a matching set so that you can swap over without having to cut off the old mounting brackets and…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

It sounds like you need the Dexter Wheel Bolt #7-262. This bolt measures 2-11/16" long from the base of the head to the threaded end. It has the same 1/2"-20 thread pitch and the 0.54" knurled end. The Studs #RG03-080 you found have…

view full answer...

Answer 12

I don't have any way of determining if the Replacement Crank Handle for etrailer and Ram 5th Wheel Landing Gear #RVLG-HDL will work with your 2007 Fleetwood Nitrous Hyperlite TT Toy Hauler or not, unfortunately. The Replacement Crank Handle…

view full answer...