Does the Dexter Nev-R-Adjust Trailer Brake Kit Come As a Pair

Question

Question:

2014 GD Solitude 305re My husband is ordering this kit but I wanted to clarify, does the kit cover both LH/RH axles, so 4 pieces? Sorry if thats a dumb question. Thank you!

asked by: Wendi S

0

Expert Reply:

Not a dumb question at all!

Brake assemblies like the Dexter Nev-R-Adjust Electric Trailer Brake Kit - 12" - Left and Right Hand Assemblies - 7K # 23-464-465 are either sold in matching pairs or as single brake assemblies for either the left or right side of the trailer # 23-464 (left) or # 23-465 (right). This particular kit is sold as a pair, so if you have tandem axles on your 2014 Grand Design Solitude 305re you'll want to order 2 of these brake kits.

Additionally, these brake kits don't come with mounting hardware included so you'll also want to consider picking that up with part # BRKH12.

expert reply by: Erik B

0

Answer 1

If you have Dexter Axle Nev-R-Adjust electric brakes on your trailer then the correct replacement brake shoes for your trailer are the following: - Left-Hand #K71-675 - Right-Hand #K71-676

view full answer...

Answer 2

Thanks for sending in the picture of your axle label. Based on that I know that the correct bearing kit is the #BK3-200 which comes with bearings and a seal for a 7k hub.

view full answer...

Answer 3

If you had an accidental grease leak within your trailer's hub/drums and the shoes were exposed to grease you will want to replace them. The brake shoe material has porosity that will let some of that wheel bearing grease work into the surface.…

view full answer...

Answer 4

The AxleTek B12E-21 and B12E-22 are the same as Electric Trailer Brake Kit #AKEBRK-6, which are manually-adjusting electric trailer brakes for 5,200 lb to 7,000 lb axles. You can purchase replacement shoes for these brake assemblies with Replacement…

view full answer...

Answer 5

The Grease Seals 10-36 Pair #RG06-070 and the Grease Seal #GS-2250DL are both double lip seals and have the same inner 2.250 inches and outer 3.376 inches diameters, as you noted. The difference between these two part numbers is that the #RG06-070…

view full answer...

Answer 6

The exact part number you referenced is no longer available, but based on my research you can use the etrailer.com Replacement Shoe and Lining Kit #AKBRKR-S-12. This kit will replace the shoes and linings on your 12 inch x 2 inch Dexter assemblies…

view full answer...

Answer 7

The 7,000 lb double-eye leaf spring we have that is closest to 26" is the 24-7/8" long 6-Leaf Double-Eye Spring for 7,000-lb Trailer Axles #e64SR. Assuming yours have flattened a good amount (which will definitely be true if the trailer is…

view full answer...

Answer 8

Yes, the Dexter trailer leaf springs like the part #DX74XR are made in the USA.

view full answer...

Answer 9

Yes, The Dexter #DX74XR will work as a direct replacement for the Dexter 072-100-01 you were looking at. These are the same length, capacity, spring count, and both use bronze bushings. It looks like the Dexter 072-100-00 uses a weird rubber bushing…

view full answer...

Answer 10

For 7k axle leaf springs like what the Dexter axle part #8327860 you referenced is designed to fit you'd want the part #DX74XR which is for a 8k axle like what you almost have but would work great still even though it's a little more capacity…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...