How To Adjust Head Angle On Reese Steadi-Flex Weight Distribution Hitch 66557

Question

Question:

Just a quick question on adjustment. How do you make the head tilt more to provide more distribution of weight? I just got it installed and if it needs tweeked I would like to know how the head adjusts. I know the Equalizer uses washers.....this one has it built in.. I plan on loading it up and doing a few measurements at the time also making sure my bars are running flush along the pads. I am hoping to have good luck with this hitch....thanks.

asked by: Mark H

0

Expert Reply:

I would be happy to help!

To adjust the head angle on your Reese Steadi-Flex Weight Distribution System w/ Sway Control - Trunnion - 12K GTW, 1.2K TW # RP66560 you will need to loosen two bolts holding the head assembly to the shank, and move the shank forward or back to get the angle you are wanting. The toothed washers will lock into groves in the head and lock in the angle you have the hitch at.

I included a video of the # RP66560 and a link to the written instructions for you to take a look at.

expert reply by: Samuel C

0

Answer 1

Weight distribution heads are adjustable to get the spring bars level or just below level with the trailer frame. Depending on the trailer frame, the head may need to be set at 90 degrees, it also may need to be tilted down as far as possible to…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

An underslung trailer coupler is one that attaches to the bottom of the trailer frame and an overslung one is one that attaches to the top of the frame. Measuring is not required if you just take a look at your coupler and see where it attaches to…

view full answer...

Answer 6

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Hey Donald, the best Blue Ox weight distribution would be the pat #BXW0550 as it has a perfect tongue weight range for your 450 lb tongue weight trailer.

view full answer...

Answer 9

Weight distribution works to distribute the tongue weight of a trailer up to the front axle of the tow vehicle so that it will sit more level and handle/brake better. That being said the systems do not "reduce" tongue weight or allow you to…

view full answer...

Answer 10

Most of the 2-5/16 inch hitch balls will use either a 1-inch diameter shank or 1-1/4 inch diameter shank. The nut size on a hitch ball with a 1-1/4 inch shank, like the Tow Ready 2-5/16 Inch Hitch Ball, part #19286, will use a 1-7/8 inch socket. A…

view full answer...

Answer 11

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...

Answer 12

Hello Dan, I can definitely help with this. It is completely normal for the Curt TriFlex brake Controller #C24VV to show the current gain setting when the brakes are applied, or when the manual override is pressed. It sounds like you have the gain…

view full answer...