Dimensions of the Hook on the Hand Winch Cable with Safety Hook # DL24043

Question

Question:

Can you send me a drawing with dimensions for this safety hook?

asked by: Joel W

0

Expert Reply:

I went out into our warehouse and pulled a Hand Winch Cable with Safety Hook # DL24043 to measure and made a video and picture that shows all of the dimensions.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Bulldog didn't have any specific dB (decibel) figures available for their # BDW15018 3400 lb capacity trailer winch, but they stated that this particular winch is no more or less noisy than any other winch of this particular size and 3400 lb…

view full answer...

Answer 2

The main two differences between the Bulldog Winch Trailer Winch part #BDW15020 and part #BDW15018 are rope diameter and motor power which results in different weight capacities. They both have the synthetic rope, wired remote, and hawse fairlead.

view full answer...

Answer 3

Since you will be more or less dragging the log, you will want a winch with at least the capacity of the heaviest log, but I would go a little heavier than that to account for longer winching distances and flat terrain should you encounter it. A 3.4K…

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 7

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 10

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 11

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 12

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Dimensions of the Hook on the Hand Winch Cable with Safety Hook # DL24043

Product Page this Question was Asked From

Continue Researching