Would Skid Plate of 2013 Dodge Charger Need to be Removed for Hitch Install

Question

Question:

My 2013 charger has an aluminum rear skid plate most do not have this. Will this hitch still fit with the skid plate?

asked by: Kyle

1

Helpful Expert Reply:

Based on how the Draw Tite hitch # 76145 installs on your 2013 Dodge Charger the skid plate you have would need to be removed.

expert reply by: Jameson C

1

Skid Plate Installed
(click to enlarge)

Answer 1

The ground clearance for the Draw-Tite Max-Frame Trailer Hitch Receiver part #76145 on your stock 2019 Dodge Charger RT is about 8-1/2 inches from the lowest point of the hitch (the bottom of the safety chain loops) to the ground. In the image I…

view full answer...

Answer 2

When we installed the Draw-Tite Max-Frame Trailer Hitch Receiver #76145 on a 2018 Dodge Challenger we found that from the ground to the top of the inside of the receiver measured 9-1/4" as you can see in the attached photo. It might be a little…

view full answer...

Answer 3

It is likely that anything mounted in Curt trailer hitch #C13093 would set off the park assist sensors on your 2012 Chrysler 300S. However, if your vehicle is anything like mine (I have a backup camera and alert system) it would only be an issue when…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 9

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 10

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...

Answer 11

To add a hitch to your 2024 Toyota RAV4, I recommend the etrailer item #e23ZR. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a 4,000 lbs towing capacity, and a 600…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Would Skid Plate of 2013 Dodge Charger Need to be Removed for Hitch Install

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching