Electric Jack Recommendation to Replace a Jack with a 2 inch Outer Diameter

Question

Question:

I currently have a 2 inch diameter lift. will this fit my trailer?

asked by: Ray

0

Expert Reply:

The Bulldog Powered-Drive Trailer Jack # BD500187 has an outer tube diameter of 2-1/4 inches and an inner tube diameter of 2-1/16 inches. This jack should be able to work on your trailer but it really depends on the diameter of the hole in your coupler. If it is larger than 2-1/4 inches then the jack will install.

If the hole is smaller than that you may have to enlarge the hole to install the # BD500187.

Or, if you can get by with a lower capacity you could use a Stromberg Carlson Electric A-Frame Tongue Jack # JET-2500. This jack has a 2 inch outer diameter just like your current jack. This jack has a 2,500 lb capacity.

expert reply by: Jameson C

0

Answer 1

The Stromberg Carlson #JET-2500 Electric Trailer Jack you referenced has a lift capacity of 2500 lbs. The jack will work just great for trailers with tongue weights less than 2500 lbs, the tongue weight of your Coachmen Cascade should certainly be…

view full answer...

Answer 2

I have provided a picture that shows the jack dimensions. These measurements were taken here by another Expert recently. The outer tube is 2 inches in diameter and the inner tube is 1-3/4 inches in diameter. The bracket to mount the jack uses a…

view full answer...

Answer 3

I have good news, our trailer jack that has a 2 inch outer diameter part #DL74MR would fit and work well. While it has a 1,000 lb weight capacity that does not mean 1,000 lb total trailer weight capacity. That capacity is the tongue weight capacity…

view full answer...

Answer 4

The rule of thumb for estimating a tongue weight is 10-15 percent of trailer weight. A 4,600 pound trailer would have a tongue weight between 460 and 690 pounds. Somewhere between a 1,000 to 2,000 pound capacity jack would be fine. Having a jack that…

view full answer...

Answer 5

For your 1999 Jayco Glacier Heritage trailer, I recommend the A-Frame Trailer Jack - Sidewind - 1,000 lbs. by Dutton-Lainson #DL22530. This is the only jack we have that has that 2 inch outer diameter upper tube. For a foot you'd want the part…

view full answer...

Answer 6

We do carry the 33" Ark Stabilizer Jack that you are looking for with part #ARK77FR. I was able to track down a few drawings that you should find helpful. These are for the 30" #ARK94FR and the 24" #ARK34FR Stabilizer jacks. I'm…

view full answer...

Answer 7

Hi Tom, I have two options to replace the electric tongue jack on your Jayco Whitehawk: Option 1: Electric Jack w/ Footplate #EJ-3520-BBX. This jack is going to be your no-frills 'get the job done' style jack. It has a 3,500lb capacity and…

view full answer...

Answer 8

I went ahead and pulled this Replacement I-Beam Jack Bracket #LC349975 from our warehouse to measure. I have attached the dimensions below. Hope this Helps.

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Yes, you can! So long as our Kenda Loadstar 5.30-12 Bias Trailer Tire with 12" White Wheel item #AM30820 is the same size and bolt pattern as what's on your Ironton trailer it can be used not only as a spare but also on your trailer with the…

view full answer...

Answer 11

For your electric jack, there are only three possible explanations for your jack not working with a charged battery. Either power is not getting to your motor, your motor is bad, or your ground connection isn't working properly. To test power,…

view full answer...

Electric Jack Recommendation to Replace a Jack with a 2 inch Outer Diameter

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching