Installation Torque Values/Specs for Draw-Tite Trailer Hitch # 75282

Question

Question:

Wind took my instructions and blew them to parts unknown. What is the torque setting for the bolts attaching the hitch to the vehicle?

asked by: Steve T

0

Expert Reply:

The Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2" # 75282 requires all hardware be torqued to 68 foot pounds according to the instructions. I've attached a photo in case you need anything else for this installation as well as a video.

expert reply by: Jason S

0

click to enlarge

Answer 1

From what little I was able to learn about the VelociRAX 5 bike rack on their website, the rack is compatible with a 2 inch hitch that has a tongue weight capacity of at least 500 lbs, and the Draw-Tite #75270 Class III hitch meets both those…

view full answer...

Answer 2

Yes, the Draw Tite hitch part #75282 is a confirmed fit for your 2009 Nissan Frontier and will work just fine with a full sized spare like what you see in the picture I attached.

view full answer...

Answer 3

You are definitely headed in the right direction! When looking into purchasing a Weight Distribution (WD) system you want to find one with a Tongue Weight (TW) range that the Total Tongue Weight (TTW) of your towing setup falls in the middle of. The…

view full answer...

Answer 4

Per the instructions which are linked for your convenience, the bolts for the Draw-Tite Max-Frame Trailer Hitch Receiver #75876 should be torqued down to 50 lb.-ft. This trailer hitch is a confirmed fit for your 2018 Subaru Forester and I have…

view full answer...

Answer 5

The Torque Specification is found in the installation instructions on our product page on the etrailer #e98846 receiver hitch. A Torque Wrench #PT87ZR would be the type that you would need to achieve that rating.

view full answer...

Answer 6

The Draw-Tite #24965 and Curt #C11402 are a lot alike. They both install on your 2018 Hyundai Sonata in basically the same fashion and have the same weight capacities. They do look a little different because the Draw-Tite has a square cross tube and…

view full answer...

Answer 7

I just spoke with my Curt representative who tells me that their aftermarket hitches will NOT interfere with the backup/parking assist sensors. They also tell me that the hands-free tailgate sensors will still work with one of their aftermarket…

view full answer...

Answer 8

The Draw-Tite Max-Frame Trailer Hitch Receiver #75282 will have the following bolt hole dimensions for your 2015 Nissan Frontier. The Bolt holes from drivers side to passenger side frame rails are 43-5/8" on center. The holes running from front…

view full answer...

Answer 9

When installing the Curt 5th Wheel/Gooseneck Custom Wiring Harness w/ 7-Pole Connector part #C57008 you will drill a 7/64" hole at all four of the mounting holes. This is what is stated in the instructions and will be the best practice to…

view full answer...

Answer 10

To add a class III hitch to your 2023 Mazda CX-9 you will want the Draw-Tite Trailer hitch item #76020. This hitch is custom fit and attaches to your Mazda with included hardware. I verified with Draw-Tite that this hitch will fit the 2023 models.…

view full answer...

Answer 11

The Class III #75282 Draw-Tite Trailer Hitch that you are interested in does comes with the six bolts needed to secure the hitch to the existing weld nuts in the frame. All of our hitches are shipped with the necessary installation hardware. If you…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Installation Torque Values/Specs for Draw-Tite Trailer Hitch # 75282

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching