Bolts Needed To Attach A Curt A or Q Series 5th Wheel Hitch Head To The Legs

Question

Question:

Just to confirm, this is the bolt kit to mount the head to the base unit on a Curt Q25 hitch? Not a rail kit...

asked by: David T

0

Expert Reply:

Correct, the Replacement Hardware for Curt A Series and Q Series 5th Wheel Hitches Item # C16125-SK4 are meant for attaching the head of the hitch to the legs.

expert reply by: Kevin C

0

Answer 1

The correct replacement hardware you are looking for is Replacement Hardware for Curt A Series and Q Series 5th Wheel Hitches #C16125-SK4. This will secure the Replacement Head Unit for Curt Q24 5th Wheel Trailer Hitch - 24,000 lbs #C16545 to the…

view full answer...

Answer 2

The Replacement Hardware for Curt A Series and Q Series 5th Wheel Hitches #C16125-SK4 contains 4 new bolts, flat washers and lock washers for your Curt A16 5th Wheel Trailer Hitch #C16120 to a set of fixed legs. We also have the Replacement Head…

view full answer...

Answer 3

For your Curt Q20 5th Wheel Trailer Hitch #C16130 you can simply swap out the legs to the Ford OEM compatible #C16017. This will make your Q20 head compatible and there is no need to purchase a completely new hitch since you are happy with the one…

view full answer...

Answer 4

The Ford OEM puck system is different than the Chevrolet/GMC OEM puck system therefore, you can't use a 5th wheel hitch from one in the other. The Ford OEM system has pucks which are much closer together than on the Chevrolet/GMC OEM system. The…

view full answer...

Answer 5

The leg kit you need to install the head and center section of your Curt Q20 hitch in the factory rail kit of your 2011 Ford F-350 with the factory towing package is the part #C16017. This would be all that you need.

view full answer...

Answer 6

We've got several hitches that will work great for you, but I really like the A Series from Curt. The Curt A20, part #C16034 will drop right into the factory puck system in your truck bed, and after minimal initial adjustment be super easy to…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Bolts Needed To Attach A Curt A or Q Series 5th Wheel Hitch Head To The Legs

Product Page this Question was Asked From

Continue Researching