Which Install Harness is Needed to for Tekonsha P3 Brake Controller and 2021 Jeep Gladiator

Question

Question:

Can you tell me if there is any difference between the Tekonsha wiring harness 3073 and 3073-P. I have a 2021 Jeep Gladiator and will be using the Tekonsha P3 90195 trailer brake controller. I see your web site states I should use the 3073-P. A friend has given me a 3073 to try with the P3, but I’m concerned that it may not be the same as the 3073-P.

asked by: Deborah L

0

Expert Reply:

A Tekonsha brake controller install harness 3073 is the same as the harness part # 3073-P which is the correct harness to install a Prodigy P3 # 90195 in your 2021 Jeep Gladiator.

expert reply by: Jameson C

0

Answer 1

We have actually run into this issue quite a few times in the past, and there is a simple fix. The reason the Curt Echo Wireless #C51180 locks up the brakes on your camper only at low speeds is due to it being paired incorrectly, usually plugging in…

view full answer...

Answer 2

After installing the Tekonsha Prodigy P3 #90195 and Custom Wiring Harness #3024-P on your 2016 Ram 1500, you will not need to take your truck to the dealer to have it flashed. The reason to take it to the dealer to get flashed is if you had to…

view full answer...

Answer 3

The Tekonsha Prodigy P3 Trailer Brake Controller #90195 can be mounted anywhere on, in, or below your dash so long as it is horizontally level and parallel with the direction of travel. You will be able to use the Tekonsha Custom Wiring Adapter for…

view full answer...

Answer 4

I attached a picture that shows the lower dash panel that needs to be removed on your 2014 Jeep Cherokee Trailhawk to find out where the brake controller install port is. I also attached an install video link to this page as well that will walk you…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

Hi Bill, The Fastway e2 Weight Distribution w/ 2-Point Sway Control #FA92-00-0450 has a tongue weight range of 200lbs - 450lbs so you'd be right around the middle of the capacity when loaded, making this a great choice. This doesn't come with…

view full answer...

Answer 8

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 9

You do have the option to utilize the air brakes on your 2023 Freightliner Cascadia to control electric trailer brakes using the Hayes Air Actuated Trailer Brake Controller, part #HA100400C. However, we mostly recommend just using an electric brake…

view full answer...

Answer 10

If you have a vehicle specific wiring harness for a brake controller then that would indicate that you have a factory tow package and subsequently would already have a 7-way at the back of your vehicle. The universal 7-way connector #ETBC7 is meant…

view full answer...

Answer 11

Sure thing, I will go ahead and list out what you need for your 2023 Kia Sportage to add a 7-way for a brake controller so you can tow with the Curt Trailer Hitch Receiver #C94WR: - T-Connector Vehicle Wiring Harness with 4-Way Flat Trailer Connector…

view full answer...

Answer 12

The Redarc Tow-Pro Liberty #RED24FR is the way to go over the Elite #RED44FR as you get the nicer functions of the Elite at a lower price. The Elite has the ability to be the more preferred proportional style of controller as well as a time-delayed…

view full answer...