Where Does Brake Controller Wiring Connect on 2014 Jeep Cherokee Trailhawk

Question

Question:

I HAVE A 2014 jeep cherokee trailhawk with factory tow package and i cant find the factory plug any suggestions? is it possible they didnt install one cause i have looked all over under dash?

asked by: Jim

0

Expert Reply:

I attached a picture that shows the lower dash panel that needs to be removed on your 2014 Jeep Cherokee Trailhawk to find out where the brake controller install port is. I also attached an install video link to this page as well that will walk you through the entire process. The correct harness to install the P3 part # 90195 you referenced is the # 3014-P.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The Tekonsha Prodigy P3 Trailer Brake Controller #90195 can be mounted anywhere on, in, or below your dash so long as it is horizontally level and parallel with the direction of travel. You will be able to use the Tekonsha Custom Wiring Adapter for…

view full answer...

Answer 2

We have actually run into this issue quite a few times in the past, and there is a simple fix. The reason the Curt Echo Wireless #C51180 locks up the brakes on your camper only at low speeds is due to it being paired incorrectly, usually plugging…

view full answer...

Answer 3

After installing the Tekonsha Prodigy P3 #90195 and Custom Wiring Harness #3024-P on your 2016 Ram 1500, you will not need to take your truck to the dealer to have it flashed. The reason to take it to the dealer to get flashed is if you had to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

You do have the option to utilize the air brakes on your 2023 Freightliner Cascadia to control electric trailer brakes using the Hayes Air Actuated Trailer Brake Controller, part #HA100400C. However, we mostly recommend just using an electric brake…

view full answer...

Answer 6

The P3 brake controller, #90195, will go into a sort of sleep mode after it detects no movement for 15 minutes. While it is on it does not draw very much power. What you can do to make sure it goes to sleep is exit the truck after turning it off,…

view full answer...

Answer 7

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 8

Hey HPA, I would go with the Air Lift kit part #AL64VJ that fits your 2019 Toyota RAV4 based on what you described and your needs. This gives you adjustable support that you can tailor as needed so that you get the exact amount of support you need…

view full answer...

Answer 9

The Redarc Tow-Pro Liberty #RED24FR is the way to go over the Elite #RED44FR as you get the nicer functions of the Elite at a lower price. The Elite has the ability to be the more preferred proportional style of controller as well as a time-delayed…

view full answer...

Answer 10

Hey Cory, thanks for reaching out! The Replacement Support Leg #TH33VK is for the 8-1/2" long Thule HideAway awnings which is what I believe will be a better match than the part #TH48VK you referenced, which is for a 10' long HideAway…

view full answer...

Answer 11

The Prodigy P3 trailer brake controller uses a 4-wire hookup. The white wire is to be grounded to the battery negative terminal; the black power wire connects to the battery hot terminal through a circuit breaker; the red wire takes in the brake…

view full answer...

Answer 12

To install the Tekonsha Prodigy P3 Trailer Brake Controller #90195 in your Freightliner S2RV chassis the wiring is behind the kick panel in the drivers compartment. There is not a connector on the wires, they are simply terminated with tape. You will…

view full answer...