Do You Have a Weld On # 84 Spindle With a Grease Zerk For E-Z Lube Hubs?

Question

Question:

Is it also available with the ez lube grease zerk?

asked by: Efrain L

0

Expert Reply:

The #84 E-Z Lube Spindle # TRU74FR matches the dimensions of the #84 Spindle # TRU64FR and will have the E-Z lube spindle and a brake flange. With the brake flange the stub will be 3/4" longer.

If necessary you can cut off the brake flange to get the correct length but otherwise it will not affect the operation of a non braking idler hub.

expert reply by: Bud M

0

Answer 1

I have three spindles that are for a 3,500-lb axle and have the bearing dimensions you have listed. The only difference is the dimension for the grease seal is 1.75 inches, not the 1.795 inches that you have mentioned. Maybe you typed in the seal…

view full answer...

Answer 2

You will need the Spindle Grease Seal Set #BB60002 for your #84 Spindle #TRU64FR with the Bearing Buddy Bearing Protectors #BB24SR.

view full answer...

Answer 3

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 4

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 5

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 6

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 7

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 8

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 9

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 10

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 11

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 12

The Tekonsha OEM Vehicle Wiring Harness #22121 that you referenced includes all the wiring and parts necessary to install a fully functional 7-Way connector and trailer brake controller. The included brake controller harness is compatible with and…

view full answer...

Do You Have a Weld On # 84 Spindle With a Grease Zerk For E-Z Lube Hubs?

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching