Are New Shocks Required When Adding Anti-Sway Bar and SumoSprings To 2013 Mercedes Sprinter 3500?

Question

Question:

In addition to upgraded sway bar and SumoSprings should I also replace the rear shocks?

asked by: John K

0

Expert Reply:

As long as the shocks on your 2013 Mercedes-Benz Sprinter 3500 are still in good shape, there is no reason to replace them.

However if they are worn out you will notice quite a difference once the replacements are installed. We do not sell shock absorbers for vehicles so I do no have a recommendation on which ones to get, though an OEM replacement would be preferred.

If you have not already decided on which sway bar and SumoSprings you plan on ordering I recommend the Roadmaster Rear Anti-Sway Bar # RM-1209-120 if your Sprinter is a standard van or cutaway model, or the # RM-1209-131 if your Sprinter is a Class C motorhome.

For the SumoSprings I recommend the SumoSprings Solo Custom Helper Springs - Rear Axle # SSR-338-54 that have a 1400lb capacity for the rear, and the # SSF-106-40 with a 500lb capacity for the front.

The combination of the anti-sway bar and SumoSprings will do a great job of absorbing bumps in the road and eliminating bouncing while also getting rid of sway.

I included videos of the products mentioned for you to take a look at.

expert reply by: Samuel C

0

Answer 1

The SumoSprings Solo Custom Helper Springs part #SSF-106-40 are what I recommend using on a 2021 Entegra Odyssey to prevent front end bounce. These springs will work to reduce bounce by absorbing road shock and vibrations while driving. They are easy…

view full answer...

Answer 2

For your 2-wheel drive model Mercedes Sprinter 3500, I recommend these following springs: - SumoSprings Solo Custom Helper Springs - Front Axle #SSF-106-47 - SumoSprings Solo Custom Helper Springs - Rear Axle #SSR-338-47 Both of these SumoSpring…

view full answer...

Answer 3

I would be happy to go over everything needed to flat tow your 2018 Honda HR-V EX 4WD with the manual transmission. Starting with the base plate kit I recommend the Roadmaster Direct-Connect Base Plate Kit - Removable Arms #RM-521570-5 which is…

view full answer...

Answer 4

Correct, the SumoSprings Solo Custom Helper Springs part #SSR-338-47 will have a softer ride than the SumoSprings Solo Custom Helper Springs part #SSR-338-54 as it's made of a softer spring. That said, the latter will also provide more support.…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Roadmasters priority when it comes to their sway bars is top notch quality and the easiest install for the customer. This typically cuts the install time down enough that you end up saving money if you pay to have the bars installed or decide to do…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hello John. I can definitely point you in the right direction, but I will need more information from you. Can you tell me the sub-model/floorplan of your 2017 Sunseeker Class C Motorhome? I will also need to know the chassis manufacturer in order to…

view full answer...

Answer 11

Hi Robert, If you're just wanting to replace the condenser unit on the rooftop and retain use of your current air distribution box and thermostat then you'll just need to determine what style connector your current unit has. If you remove the…

view full answer...

Answer 12

Thanks for the question Mike; the answer is yes, the 15,000 Btu Advent Air Low Profile RV Air Conditioner - Black #ADV56FR and White #ADV29FR do indeed work with your Dometic set up.

view full answer...