Which Wiring Harness Do I Need For My 2003 Ford Windstar?

Question

Question:

ford windstar manufactured o5/2003 will light kit hm40615 fit

asked by: JIMMY L

0

Expert Reply:

Your 2003 Ford Windstar will require the Plug-N-Tow (R) Low-Side Switching Hardwire Kit # 36345 since it was produced after October 2002. Ford switched to a negative power input on these vehicles.

The Hopkins Plug-In Simple Vehicle Wiring Harness # HM40615 is only for the Windstar produced before November 2002.

expert reply by: Bud M

0

Answer 1

If you try to splice a simple 4-way connector to your 2003 Ford Windstar you will not get proper taillight function and will cause electrical problems with the vehicle if you hook up a trailer. At the very least you will blow fuses and you could…

view full answer...

Answer 2

Hopkins tail light converter #HM48895 is a universal fit item so you can use it on your 2003 Ford Windstar. There are other, custom fit options available though. Check the build-date sticker in the door jamb of your Windstar. If it was built before…

view full answer...

Answer 3

To be able to install a trailer connector on your 2004 Thunderbird you will need wiring like part #36345 that is specifically designed for your wiring. This is a hardwire installation. We do not offer a plug-and-play option. I found that your…

view full answer...

Answer 4

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 5

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 6

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 12

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Which Wiring Harness Do I Need For My 2003 Ford Windstar?

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching